E3X-ZV Fiber Amplifiers, Communications Unit and Accessories Ratings and Specifications *1.Mutual interference prevention function in the Response Time Priority Mode: 2 units: 350 µs; 3 units: 400 µs / In the Unit Number Priority Mode: 4 units: 700 µs *2.Mutual interference prevention function in the Unit Number Priority Mode: 4 units:
1.6 ms 88 Fiber Sensor Features Selection Guide Fiber Units Standard Installation Threaded Hex-shaped Cylindrical Saving Space Flat Sleeved Beam Improvements Small Spot High Power Narrow view BGS Transparent Objects Retro- reflective Limited- reflective Environmental Immunity Chemical- resistant, Oil-resistant Bending Heat- resistant Applications Area Detection Liquid-level Vacuum FPD, Semi, Solar Installation Information Fiber Amplifiers, Communications Unit, and Accessories Technical Guide and Precautions Model Index 88 Item Type NPN output PNP output Connecting method Standard models NPN output E3X-ZV11 E3X-ZV6 PNP output E3X-ZV41 E3X-ZV8 Connecting method Pre-wired Wire-saving Connector Outputs 1 output Light source (wavelength) Red, 4-element LED (625 nm) Power supply voltage 12 to 24 VDC ±10%, ripple (p-p) 10% max.
Power consumption Normal mode: 720 mW max. (Power supply voltage 24 V: Current consumption 30 mA max. / Power supply voltage 12 V: Current consumption 60 mA max.) Eco function ON: 530 mW max. (Power supply voltage 24 V: Current consumption 22 mA max. / Power supply voltage 12 V: Current consumption 44 mA max.) Control output Load power supply voltage: 26.4 VDC, open collector output type (NPN or PNP output differs depending on the type.) Load current: 100 mA max. (Residual voltage: Load current less than 10 mA: 1 V max., load current 10 to 100 mA: 2 V max.) OFF current: 0.1 mA max. Indicators 7-segment displays (Threshold Level display: green, Incident Light Level display:
red) Display direction: Switchable between normal and reversed. Smart Tuning Indicator (green) Standard models only: OUT indicator (orange) 2-channel models only: OUT1/2 indicator (orange), CH Indicator (green) Protection circuits Power supply reverse polarity protection, output short-circuit protection and output reverse polarity protection Response time Super-highspeed mode (SHS) Operate or reset: 50 μsμ High-speed mode (HS) Operate or reset: 250 μs *1 Standard mode (Stnd) Operate or reset: 1 ms *3 Giga-power mode (GIGA) Operate or reset:
16 ms Sensitivity adjustment Smart Tuning (2-point tuning, power tuning, percentage tuning (−99% to 99%), maximum sensitivity tuning, full auto tuning, position tuning) or manual adjustment Maximum connectable Units 16 Mutual interference prevention function Emission cycle setting switching type (up to 4 units) Functions DPC (Dynamic Power Control) Yes ATC (Active Threshold Control) Yes Timer Select from timer disabled, OFF-delay, ON-delay or one-shot timer: 1 to 9,999 ms Zero reset Negative values can be displayed. (Threshold value is shifted.) Resetting settings Select from initial reset (factory defaults) or user reset (saved settings).
Eco mode Select from OFF (digital display lit) and Eco ON (digital display not lit). Power tuning Select from ON or OFF. Ambient illumination (Receiver side) Incandescent lamp: 20,000 lx max., Sunlight: 30,000 lx max. Ambient temperature range Operating: -25°C to 55°C Storage: -30°C to 70°C (with no icing or condensation) Ambient humidity range Operating and storage: 35 to 85% (with no condensation) within the surrounding air temperature range shown above Insulation resistance 20 MΩ min.
(at 500 VDC) Dielectric strength 1,000 VAC at 50/60 Hz for 1 min Vibration resistance (destruction) 10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance (destruction) 500 m/s2 for 3 times each in X, Y, and Z directions Weight (packed state/Sensor only) Approx. 95 g/ approx. 65 g Approx. 45 g/ approx. 20 g Materials Case Polycarbonate (PC). Cover Polycarbonate (PC) Cable PVC Accessories Instruction manual, Compliance sheet