CW-C8000 Series Paper Feeder/Paper Rewinder Designer’s Guide (EN)

Paper Feeder/Paper Rewinder Designer's Guide M00163100 Rev.A

Стр. 1

Cautions 1. This document shall apply only to the product(s) identified herein. 2. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. 3. The contents of this document are subject to change without notice. Please contact us for the latest information. 4. While every precaution has been taken in the preparation of this document, Seiko Epson Corporation assumes no responsibility for errors or omissions. 5.

Neither is any liability assumed for damages resulting from the use of the information contained herein. 6. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. 7.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Seiko Epson Corporation. 8. When this product is used for applications requiring high reliability/safety, such as transportation devices related to aviation, rail, marine, automotive, etc.; disaster prevention devices; various safety devices, etc.; or functional/precision devices, etc., you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.

Because this product was not intended for use in applications requiring extremely high reliability/safety, such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care, etc., please make your own judgment on this product's suitability after a full evaluation. Trademarks Product names used herein are for identification purposes only and may be trademarks of their respective owners. ©Seiko Epson Corporation 2024 2

Стр. 2

Contents

Contents ■ Contents....................................................................................................................................3 ■ Paper Feeder/Paper Rewinder Designer's Guide..............................................................4 Paper Specification............................................................................................................................................................4 Preparation before Use ....................................................................................................................................................4 Print Speed Setting............................................................................................................................................................5 Paper Load............................................................................................................................................................................5 Paper Curl..............................................................................................................................................................................6 Paper Angle for Feeding and Ejecting........................................................................................................................6 Position of Paper Feeder and Paper Rewinder ........................................................................................................7 Locations of Holes and Shafts on the Bottom Case...............................................................................................8 3

Стр. 3

Set the Media Source to [Rear Feed]

Paper Feeder/Paper Rewinder Designer's Guide The CW-C8000 Series is designed to print with paper fed from inside (roll paper) or fed from outside the printer (roll paper or fanfold paper) or while connected to the optional paper rewinder (TU-RC8000). If you use an external roll paper feeder and/or paper rewinder with the printer, read this section carefully to know required settings and requirements for using the external devices, and perform adequate verification before starting actual printing. Paper Specification The following types of paper are supported when using an external roll paper feeder and/or paper rewinder with CW-C8000 Series printers. 1.

For the latest information on detailed paper specifications and the base paper used in roll paper, contact qualified service personnel. 2. For details on paper specification, see the CW-C8000 Series Technical Reference Guide. 3. If cutting continuous paper for each page, the paper rewinder cannot be used. Preparation before Use If you use an external roll paper feeder and/or paper rewinder with the printer, perform the following items before use. Set the Media Source to [Rear Feed] Set the Media Source to [Rear Feed]. For details on this setting, refer to the CW-C8000 Series User's Guide.

• Make sure that the external roll paper feeder and/or paper rewinder does not interfere with the back feed in the following Print Mode. ∗ Do not cut (stop at cut position) Back feed amount Approx. 200 mm {7.87 in.} ∗ Do not cut (stop at specified position) Back feed amount Approx. 200 to 250 mm {7.87 to 9.84 in.} 4 Paper forms Paper types Paper shapes Backing paper width Label width Label length Full-page label (no marks) Plain paper label Matte label Texture label Synthetic label Glossy label High glossy label Glossy film label Roll paper If also using a roll paper feeder and rewinder: 50 to 112 mm {1.97 to 4.41 in.} If using only a rewinder:

25.4 to 112 mm {1.00 to 4.41 in.} If also using a roll paper feeder and rewinder: 46 to 108 mm {1.81 to 4.25 in.} If using only a rewinder: 21.4 to 108 mm {0.84 to 4.25 in.} - Full-page label (Black Marks) Die-cut label (Gap) 8 to 1016 mm {0.31 to 4.57 in.} Die-cut label (Black Marks)

Стр. 4