Руководство по эксплуатации Epson проектор (EN)

Terms of Use Terms of Use for “Supplemental Guide for Display Status Menu” September 2021 Seiko Epson Corporation 1. The copyright of "Supplemental Guide for Display Status Menu" (hereinafter referred to as "this document") belongs to Seiko Epson Corporation (hereinafter referred to as "the company"). You may print one copy of this document and use it only for the purpose of using the company's projector products. You may not reproduce, reprint, modify, or transmit this document, in whole or in part, without prior permission from the company. 2. The content of this document is subject to change without notice. Make sure you understand these points before use. 3.

You use this document at your own risk. The company shall not be liable for any direct, indirect, special, incidental, consequential, or other damage resulting from your use of, or inability to use, this document. ©2021 Seiko Epson Corporation Page 2/10 Version 1.1.0

Стр. 2

Display Status ©2021 Seiko Epson Corporation Page 3/10 Version 1.1.0 Category Item Description System System Status Laser Status Last Event Intake Air Temp Internal Temp Lv Displays the system status. Displays the main status. System Status Displays the operating status of the system. OK: The projector is in normal operating mode. Warm-Up: The projector is warming up. Standby: The projector is in standby mode. Cool Down: The projector is cooling down. Temp Error: Temperature error due to overheating. Projector has turned off. Leave it turned off to cool down for 5 minutes. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.

• Make sure the environmental temperature is not too hot. • Clean or replace the air filter. For details, refer to the Userʼs Guide . • If operating the projector at high altitude, set the [High Altitude Mode] setting to [On] in the projector's [Installation] menu. • If the problem persists, unplug the projector and contact Epson for help. Fan Error: A fan error has occurred. Turn the projector off, unplug it, and contact Epson for help. Sensor Error: Turn the projector off, unplug it, and contact Epson for help. Internal Error: An internal error has occurred. Turn the projector off, unplug it, and contact Epson for help. Temp Warning: A high temperature warning occurred.

• Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter. • Make sure the environmental temperature is not too hot. Laser Error: Turn the projector off, unplug it, and contact Epson for help. Laser warning: Turn the projector off, unplug it, and contact Epson for help. Laser Status Displays the operating status of the light source. Last Event Displays the latest warnings or errors. Intake Air Temp Displays the air intake temperature. Internal Temp Lv Displays the projector's internal temperature in five levels.

Стр. 3

Display Status ©2021 Seiko Epson Corporation Page 4/10 Version 1.1.0 Category Item Description Displays the operation time and light source information. Operation Time Displays the projector's total operation time. Laser Op. Time Displays the total operation time of the laser light source. Displays the status of the current input source. Source Displays the current source. Display example: HDMI Signal Status Displays the identification results of signals. • Available: This signal can be displayed. • No Signal: No signal is being input. • Not supported: An input signal has been detected, but cannot be displayed because it is not supported. Resolution Displays the resolution.

Display example 1: 640 x 480: A signal with an effective resolution of 640 pixels (wide) x 480 lines (high) Display example 2: 1920 x 1080: A signal with an effective resolution of 1920 pixels (wide) x 1080 lines (high) Refresh Rate Displays the refresh rate and scanning method. Display example 1: 24p = Refresh Rate 24 [Hz], Scan Mode: Progressive Display example 2: 60i = Refresh Rate 60 [Hz], Scan Mode: Interlace ColorSamp./Depth Displays the color sampling and bit depth. Display example 1: YCbCr444/8bit Display example 2: RGB/10bit ☞ Notes When YCbCr422 is detected at the following input ports, "-" is displayed because the bit depth cannot be analyzed.

• HDMI Color Space Displays the color space. • Auto(***): When set to [Auto], the color space that is automatically determined from the input signal is displayed instead of ***. Display example: Auto(BT.709) • BT.709: Displayed when the input signal is being processed using BT.709. • BT.2020: Displayed when the input signal is being processed using BT.2020. ☞ Notes • BT.709: Mainly used for DVDs and conventional TV broadcasts. • BT.2020: Mainly used for high-quality image content such as HDR.

Стр. 4

Display Status ©2021 Seiko Epson Corporation Page 5/10 Version 1.1.0 Category Item Description Dynamic Range Displays the dynamic range. • Auto(***): When set to [Auto], the dynamic range that is automatically determined from the input signal is displayed instead of ***. Display example: Auto(SDR) • SDR: Displayed when the input signal is being processed using SDR. • HDR10: Displayed when the input signal is being processed using HDR10. • HDR10+: Displayed when the input signal is being processed using HDR10+. • HLG: Displayed when the input signal is being processed using HLG. ☞ Notes • SDR: Mainly used for DVDs and conventional TV broadcasts. • HDR10:

This is one of the HDR standards and is mainly used for Ultra HD Blu- • HDR10+： This is one of the extended standards of HDR and is mainly used for Ultra HD Blu-rays. Its dynamic metadata allows you to process images dynamically and display images with gradations that are more suitable for each scene than HDR10. • HLG: This is one of the HDR standards and is mainly used for TV broadcasts. With a brightness gradient approximately 10 times greater than SDR, this allows you to display realistic images. Video Range Displays the video range. • Auto(***): When set to [Auto], the video range that is automatically determined from the input signal is displayed instead of ***. Display example:

Auto(Limited) • Limited(16-235): Displayed when the input signal is being processed using Limited. • Full(0-255): Displayed when the input signal is being processed using Full. ☞ Notes • Limited(16-235): Usually selected when the input signal is a YCbCr signal. • Full(0-255): Usually selected when the input signal is an RGB signal. • If images look over-exposed or under-exposed, set [Signal I/O] - [Signal Format] in the projector's menu to [Full (0-255)]. Frame Interp. Displays the Frame Interpolation setting. Setting Value: Off, Low, Medium, or High Version Serial Number Main Video2 Sub HDMI Pixel Shift Displays the serial number and firmware version.

Serial Number Displays the serial number. Main Displays the embedded software main version. Video2 Displays the embedded software version. Sub Displays the embedded software version. HDMI Displays the embedded software version. Pixel Shift Displays the embedded software version. Network Wired Projector Name Connection Mode DHCP IP Display IP Address MAC Address Displays the wired network status. Projector Name Displays the name used to identify the projector when connected to a network. Connection Mode Displays the connection path for a wired network. DHCP Displays the DHCP settings. IP Display Displays the IP address display settings. IP Address Displays the IP address.

MAC Address Displays the MAC address.

Стр. 5