1D/2D Label Verification Kit Quick Start Guide (EN)

Technical Note 1D/2D Label Verification Kit Purpose This document provides guidance to users of the 1D/2D Label Verification Kit , part number SLN-0000047 . This kit consists of a light, lens, smart camera, and other accessories required to implement a verification system that is compliant with the requirements of ISO 15415 , ISO 15416, and AIM DPM guidelines , or a custom verification configuration . Kit Contents Part Number Quantity Description 98-9000137-01 1 Kit, Smart Series Pharmalite, HAWK MV-4000 8013-0000-0104 1 HAWK MV-4000, 2 MP, Mono, AV + VS + Verification/OCV 98-000265-02 1 Kit, Ref.

Calibration Card, AutoVISION 98-9000154-01 1 Lens, C-Mount, F1.6/16 mm, HD, 2/3", Fujinon 61-9000132-01 1 Cable, Adapter, HAWK MV-4000 to QX-1 080-044700 1 Spacer, M/P, 1 mm THK 83-220127-XX 1 User Documentation (This document) Copyright ©2018 Omron Microscan Systems, Inc. P/N 83-220127-08 Rev A Quantity Description 1 Kit, Smart Series Pharmalite, HAWK MV-4000 1 HAWK MV-4000, 2 MP, Mono, AV + VS + Verification/OCV 1 Kit, Ref. Calibration Card, AutoVISION 1 Lens, C-Mount, F1.6/16 mm, HD, 2/3", Fujinon 1 Cable, Adapter, HAWK MV-4000 to QX-1 1 Spacer, M/P, 1 mm THK 1 User Documentation (This document) P/N 83-220127-08 Rev A

Стр. 1

1 D/2D Label Verification Kit Quick Start Guide Accessories The required accessories are an Ethernet cable for the camera, a power supply, and power cables for the camera and lighting. The selection of accessories depends on the details of the installation, such as required cable length, availability of suitable power, and whether the installation will employ continuous or strobed lighting. The minimum set of accessories required to complete a bench-top installation is shown below. In the configuration shown, the HAWK MV-4000 camera and the illuminator share a power supply via a QX-1 Connection Block.

Accessories – Hardware Configuration 4 The Ethernet cable is connected to “100/1G” on the camera. 1 The adapter cable is connected to “Power” on the camera. 2 3 Pharmalite Illuminator Power Supply Photo Sensor 2 Copyright ©201 8 Omron Microscan Systems, Inc. Item Part Number Description 1 8013-0000-0104 HAWK MV-4000 Smart Camera, 2 MP, Mono, AV + VS + Verification/OCV 2 61-000162-02 Cordset, Common, M12 12-Pin Socket to M12 12-Pin Plug, 1 m or 61-000148-02 Cordset, Common, M12 12-Pin Socket to M12 12-Pin Plug, 3 m 3 61-9000132-01 Cable, Adapter, HAWK MV-4000 to QX-1 4 61-9000134-0X Cordset, Host, Ethernet, M12 8-Pin Plug to RJ45

Стр. 2

1D/2D Label Verification Kit Quick Start Guide Mounting Positions The 1D/2D Label Verification Kit is designed to be mounted with the bottom surface of the light 1 9/16 inches (39.7 mm) above the surface of the mark being inspected. At this position the back of the camera is 6 7/8 inches (174.0 mm) above the surface. At this distance the field of view with the supplied 16 mm lens and 1 mm lens spacer is 2.00” (50.8mm) x 1.06” (27.0mm).

Mounting Options and Hardware The 1D/2D Label Verification Kit can be mounted using one or more of the six ј inch (6.6 mm) through-holes in the Pharmalite back plate (using customer-supplied fasteners) or by means of the four M4-tapped holes that are available on the top surface of the camera. Alternate Mounting Option You also have the option of using the threaded mounting holes of the HAWK MV-4000 to mount the camera with 4 M4x0.7 mm screws. 3 Copyright ©201 8 Omron Microscan Systems, Inc.

Стр. 3

1D/2D Label Verification Kit Quick Start Guide Applicability to Verification Standards The verification methodologies described in this document do not meet the standard light angle geometries for ISO 15415, ISO 15416, and AIM DPM, but the methods described here can be considered an alternate geometry. This kit supports a camera and 60 degree dark field lighting configuration that is consistent with the requirements of ISO 15415 (Information technology — Automatic identification and data capture techniques — Bar code print quality test specification — Two-dimensional symbols) and AIM DPM 1-2006 AIM (Direct Part Mark Quality Guidelines).

The equivalent standard for 1D verification (ISO 15416) calls for a single source of oblique (45 degree) illumination in the reference configuration, while the Pharmalite used in the 1D/2D Verification Kit provides an alternate geometry of oblique 60 degrees. AutoVISION 2.0/Visionscape 6.0 and higher support the verification methodologies defined in these standards for the ECC 200 Data Matrix symbol. ISO 15415 is best-suited to high-contrast 2D printed marks, ISO 15416 are best-suited to high-contrast 1D printed marks, and AIM DPM guidelines are intended for direct part marks.

Lighting Configurations All the applicable standards require that the camera be mounted perpendicular to the marked surface. ISO standards require at least 8 pixels per element . The AIM standard follows the ISO 15415 standard. The minimum symbol element size (cell size or 1D narrow bar) that will provide the required number of pixels per element with the supplied camera and lens is 0.009 inches . The ISO standards indicate basic “reference optical geometries” – meaning lighting positions – and alternate geometries that include oblique degrees incident light (Pharmalite) .

If an alternate geometry such as Pharmalite is used, you must enter the 60 degree angle and wavelength (W) into AutoVISION’s Symbol Quality Verification Tool and ensure that the angle and wavelength are also included in any resulting verification report. Alternate Applications If called upon to verify 1D symbols that are larger than those that can be graded with the 1D/2D Label Verification Kit [maximum field of view 2.00” (50.8mm) x 1.06” (27.0mm)], you may find that the Large Linear Verification Kit, part number SLN-0000048 , can be usefully applied. The Large Linear Verification Kit can also be used if strict adherence to the reference geometry and lighting wavelength is required.

The 1D/2D Label Verification Kit can be used to implement Optical Character Verification (OCV) on glossy labels either in combination with 1D or 2D symbol verification or as a stand-alone application. Marking Method The 1D/2D Label Verification Kit works best when the mark is on a specular/reflective surface (ink on glossy label stock). The Dot Peen Verification Kit, part number SLN-0000046 , may be a better solution with marks that are on matte diffuse surfaces (ink on matte paper). The Dot Peen Verification Kit should be used for dot peen marks in almost all circumstances. The choice for laser marks depends on the form or the mark.

If annealing/ablation has occurred, then the Dot Peen Verification Kit is appropriate if the substrate is dark. Operation The Pharmalite illuminator is designed to be mounted 1 9/16” (39.7 mm) from the object being inspected. Configuration and use of AutoVISION verification is covered in detail in the Symbol Quality Verification Tool section of the AutoVISION Software User Manual (“autovisionmanual.pdf”, located in C:\Microscan\ Vscape\Documentation after AutoVISION installation) and also in AutoVISION Help, which can be accessed from the File menu in AutoVISION software. 4 Copyright ©201 8 Omron Microscan Systems, Inc.

Стр. 4