HOME 3.1 SPECIFICATIONS: ENGINE FASTENER TORQUE VALUES IN THIS CHAPTER The table below lists torque values for all fasteners presented in this chapter. FASTENER TORQUE VALUE NOTES 5 mm head bolts 9.7 Nm 86 in-lbs 3.9 CYLINDER HEAD, Installation Cam chain tensioner 100 Nm 74 ft-lbs 3.8 CAMSHAFTS, DRIVE CHAINS AND CAM- SHAFT TIMING, Installation of Cams, Timing Chains and Camshaft Timing Cam chain tensioner 100 Nm 74 ft-lbs 3.8 CAMSHAFTS, DRIVE CHAINS AND CAM- SHAFT TIMING, Installation of Cams, Timing Chains and Camshaft Timing Cam cover fasteners 9.7 Nm 86 in-lbs 3.8 CAMSHAFTS, DRIVE CHAINS AND CAM- SHAFT TIMING, Installation of Cams, Timing Chains and Camshaft Timing/Special method:
Install in sequence:
cable ties first, spark plug hole gasket second Cam journal caps 9.7 Nm 86 in-lbs 3.8 CAMSHAFTS, DRIVE CHAINS AND CAM- SHAFT TIMING, Installation of Cams, Timing Chains and Camshaft Timing Cam journal caps 9.7 Nm 86 in-lbs 3.8 CAMSHAFTS, DRIVE CHAINS AND CAM- SHAFT TIMING, Installation of Cams, Timing Chains and Camshaft Timing Cam journal caps 9.7 Nm 86 in-lbs 3.9 CYLINDE R HEAD, Head Assembly Cam journal caps 9.7 Nm 86 in-lbs 3.9 CYLINDE R HEAD, Head Assembly Camshaft sprocket fasteners 23 Nm 17 ft-lbs 3.8 CAMSHAFTS, DRIVE CHAINS AND CAM- SHAFT TIMING, Installation of Cams, Timing Chains and Camshaft Timing Connecting rod caps 27 Nm 20 ft-lbs 3.11 ENGINE BOTTOM END SERVICE, Crank- shaft, Piston and Cylinder Liner Removal/Installa- tion/Tighten to torque and then tighten an additional 90 degrees Connecting rod caps 27 Nm 20 ft-lbs 3.11 ENGINE BOTTOM END SERVICE, Crank- shaft, Piston and Cylinder Liner Removal/Installa- tion/Tighten to torque and then tighten an additional 90 degrees Head bolts, initial torque 35 Nm 25.8 ft-lbs 3.9 CYLINDER HEAD, Installation/Special method:
See Head bolts, second torque Head bolts, second torque 20 Nm 14.8 ft-lbs 3.9 CYLINDER HEAD, Installation/Special method: Apply initial torque. Loosen each bolt one full turn (360°). Apply second torque. Position the Torque Angle Gauge and tighten bolt an additional 90°.
Oil filter mount fasteners 9.7 Nm 86 in-lbs 3.13 OIL FILTER MOUNT, Removal/Installation Oil pump fasteners 9.7 Nm 86 in-lbs 3.12 OIL PUMP, Removal/Installation Primary chain fixed tensioner fastener 3.8 CAMSHAFTS, DRIVE CHAINS AND CAM- SHAFT TIMING, Primary Cam Drive Installation oner fastener 9.7 Nm 86 in-lbs 3.8 CAMSHAFTS, DRIV SHAFT TIMING, Primary Primary chain hydraulic t fasteners ensioner 9.7 Nm 86 in-lbs 3.8 CAMSHAFTS, DRIV SHAFT TIMING, Primary E CHAINS AND CAM- Cam Drive Installation Primary gear fasteners 10 Nm 88 in-lbs 3.11 ENGINE BOTTOM shaft, Piston and Cylinde tion/Use a crisscross pat END SERVICE, Crank- r Liner Removal/Installa- tern when tightening 2009 VR SC Service:
Engine 3-1