U.S. Army Aviation and Troop Command · ADS-43A-HDBK · 67 стр.
Оригинальное название: ADS-43A-HDBK Aircraft Engine Components Qualification Handbook PDF
Downloaded from https://www.everyspec.com ADS-MA-HDBK AERONAUTICAL DESIGN STANDARD HANDBOOK QUALIFICATION REQUIREMENTS AND IDENTIFICATION OF CRITICAL CHARACTERISTICS FOR AIRCRAFT ENGINE COMPONENTS UNITED STATES ARMY AVIATION AND TROOP COMMAND ST.LOUIS, MISSOURI AVIATION RESEARCH AND DEVELOPMENT CENTER DIRECTORATE FOR ENGINEERING DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited.
Downloaded from https://www.everyspec.com ADS-43A-HDBK ADS-43A-HDBK This Army Aeronautical Design Standard (ADS) Handbook is prepared under the authorization of Army Materiel Command (AMC) Regulation 70-32. Any recommended corrections, additions, or deletions which may be used in improving this document should be addressed to: U.S. Army Aviation and Troop Command ATTN: AMSAT-R-E 4300 Goodfellow Blvd. St. Louis, MO 63120-1798 This handbook is for guidance only. This handbook cannot be cited as a requirement. If it is, the contractor does not have to comply. APPROVED: BARRY J. BASKETT Director of Engineering
Downloaded from https://www.everyspec.com ADS-43A-HDBK TABLE OF CONTENTS SECTION 1 GENERAL QUALIFICATION REQUIREMENTS PAGE 1.1 INTRODUCTION 1.1.1 Purpose 1.1.2 Implementation 1.1.3 Use of Alternate Suppliers / Processors 1.1.4 Definitions 1.2 APPLICABLE DOCUMENTS 4 1.3 GENERAL REQUIREMENTS 5 1.3.1 General 5 1.3.2 Source Control Drawings 5 1.3.3 Dimensional Substantiation 5 1.3.4 Material Substantiation 6 1.3.5 Process Substantiation 6 1.3.6 Manufacturing Process Control 6 1.3.7 Flight Safety Parts 7 1.3.8 Approval to Conduct Testing 7 1.3.9 Parts Not Requiring Qualification 7 1.4 TEST REQUIREMENTS 1.4.1 General 1.4.2 Environmental Tests 1.5 APPROVAL OF TEST RESULTS 1.5.1 Test Component Evaluation 15.2 Rejection and Retest 1.5.3 Alternate Source Approval 1.5.4 Change in Approved Sources / Processes i
Downloaded from https://www.everyspec.com ADS-43A-HDBK SECTION 2 IDENTIFICATION OF CRITICAL CHARACTERISTICS PAGE 2.1 INTRODUCTION 1 1 2.2 CRITICAL CHARACTERISTICS 2.2.1 Materials 2.2.2 Manufacturing 1 1 11 1 3 2.2.3 Processes 2.2.4 Inspection Methods 2.2.5 Typical Critical Characteristics (Baseline) 1 7 1 8 1 9 2.3 TEST DESCRIPTION 2 4 Code A High Cycle Fatigue Tests 2 4 Code B Seal Tests 25 Code C Bearing Tests 2 7 Code D Gear Tests 28 Code E Endurance Tests 2 9 Code F Low Cycle Fatigue Tests 30 Code G Engine Performance Tests 32 Code H Special Tests 3 3 Code I Electronic Control Testing 33 Code J Fuel Control Testing 33 Code 33.
Code M Thermocouple Assembly 34 Code N Electrical Tests 3 4 Code 0 Fuel Nozzle 35 2.3.1 Test Code Guidelines 35 & Pneumatic) 33 Code L Wiring Harness K Valve Assembly (Hydraulic SECTION 3 OVERHAUL REQUIREMENTS PAGE 3.1 INTRODUCTION 4 1 3.2 CRITICAL CHARACTERISTICS 4 1 3.2.1 Materials 4 1 ii