Demontage und Montage, Motor komplett Disassembly and reassembly of complete engine Dйmontage et montage moteur complet Despiece y ensamblado conjunto de motor Inhalts-Verzeichnis Table of Contents Sommaire Indice Werkstatthandbuch BFM 1012/E, BFM 1013/E English 4. Disassembly and reassembly of complete engine Page Dismantling engine ___________________________________ 4.00.01 - 4.00.16 Reassembling engine:
Oil spray nozzles ___________________________________ 4.00.17 Tappets/camshaft ___________________________________ 4.00.18 Crankshaft bearings ___________________________________ 4.00.18 - 4.00.21 Mass balancing shafts BFM 1012 ___________________________________ 4.00.22 - 4.00.27 Drive gear/governor ___________________________________ 4.00.27 Control rod ___________________________________ 4.00.27 - 4.00.28 Timing chest cover ___________________________________ 4.00.28 - 4.00.29 Front cover ___________________________________ 4.00.29 - 4.00.30 Piston with connecting rod ___________________________________ 4.00.30 - 4.00.31 Installing injection pump ___________________________________ 4.00.32 - 4.00.40 Flywheel/V-belt pulley ___________________________________ 4.00.41 Cylinder head ___________________________________ 4.00.42 - 4.00.47 Shutdown solenoid ___________________________________ 4.00.47 Injector/injection lines ___________________________________ 4.00.48 - 4.00.49 Air intake/exhaust manifold ___________________________________ 4.00.49 - 4.00.50 Cylinder head cover ___________________________________ 4.00.50 - 4.00.51 Lube oil cooler ___________________________________ 4.00.51 - 4.00.52 Coolant pump ___________________________________ 4.00.52 - 4.00.54 Fuel pump ___________________________________ 4.00.54 Oil suction pipe/oil pan ___________________________________ 4.00.54 - 4.00.56 Governor ___________________________________ 4.00.57 - 4.00.58 Cable harness ___________________________________ 4.00.59 Adapter housing ___________________________________ 4.00.60 Starter ___________________________________ 4.00.61 Breather pipe ___________________________________ 4.00.61 - 4.00.62 Цil pressure switch ___________________________________ 4.00.62 - 4.00.63 Crankcase breather ___________________________________ 4.00.63 Exhaust turbocharger ___________________________________ 4.00.64 - 4.00.65 Oil return pipe/pressure oil pipe ___________________________________ 4.00.65 - 4.00.68 Intake elbow ___________________________________ 4.00.68 - 4.00.70 Charge air elbow BFM 1013 ___________________________________ 4.00.70 - 4.00.71 Oil dipstick ___________________________________ 4.00.71 Alternator ___________________________________ 4.00.72 Tensioning V-belt ___________________________________ 4.00.72 - 4.00.74 Engine mounting/mounting feet ___________________________________ 4.00.74 Removing and refitting components for integrated cooling system , BFM 1012:
Removing components ___________________________________ 4.00.75 - 4.00.82 Refitting components ___________________________________ 4.00.83 - 4.00.94 4 Replacing shaft seals on complete engine Timing chest cover flywheel end ___________________________________ 4.00.95 - 4.00.96 Front cover ___________________________________ 4.00.96 - 4.00.97 Removing and refitting PTOs:
Removing and refitting air compressor _________________________________ 4.00.99 - 4.00.100 Removing and refitting power steering pump ____________________________ 4.00.101 - 4.00.102 Removing and refitting hydraulic pump_________________________________ 4.00.103 Removing and refitting hydraulic pump together with bracket _______________ 4.00.105 - 4.00.107 Replacing injection pumps in case of service ___________________________ 4.00.109 - 4.00.112