OM3043 Operation - Section 3 Operating Instructions Page 30-3 10. Before leaving this position, look under the lower edge of the chassis to be sure the flexible duct that carries the air from the main blower to the final drive housing is in good condition with no holes or breakage. Also look up at the main hydraulic pumps to see that there is no leakage or any other unusual condition with pumps or pump drive shafts. limit switch. Remove any mud/dirt accumulation from switch. 19. Move on around the fuel tank, inspect the fuel quantity gauge, (this should agree with what will show on the gauge in the cab).
Inspect the attaching hardware for the fuel tank at the upper saddles, and then at the lower back of the tank for the security and condition of the mounts. 11. Move on around the dual tires, check to see that all lugs/wedges are in place and tight. Inspect wheel cover for cracks or damage, and check latches to be sure they are properly latched. Inspect wheel for any leakage that may be com- ing from inside the wheel cover that would indi- cate brake leakage, or wheel motor leakage. 20. Move in behind the right front wheel, and inspect the steering cylinder, suspension attaching hardware and suspension extension, as well as greasing and attaching hardware for the steering cylinder.
Inspect the hub and brakes for leaks and any unusual condition. Be sure the suspension protective boot is in good condition. Check dual tires for cuts, damage or bubbles and that inflation appears to be correct. If truck has been run on a flat, the tire must be cooled before parking truck inside . Inspect for any rocks that might be lodged between dual tires, and that rock ejector is in good condition and straight so that it can not damage a tire. 21. Move out and around the right front wheel, inspect that all lugs/wedges are in place and tight. 22. Move in behind the front of the right front wheel, check hub and brakes for leaks and any unusual condition.
Inspect steering cylinder for security and for proper greasing. Inspect the engine compartment for any leaks and unusual condition. Inspect the fan guard, and belts also for any rags or debris behind radiator. Turn work light off, if used, and secure the ladder up and latched. Inspect auto lube system. See Mainte- nance Section 4 for specific details concerning auto lube system. 12. Inspect left rear suspension for damage and for proper inflation, and that there are no leaks. Inspect also for proper greasing, and that cov- ers over the chromed piston rod are in good condition. 13. Open rear hatch cover, turn on work light, if nec- essary.
Inspect for leaks around wheel motor mounting to rear housing and brake hoses and fittings. Be sure that covers on wheel motor sump are in place, and that there are no rags or tools left behind. Inspect condition of hatch cover gasket, report any bad gasket to mainte- nance. Turn off work light if used, close and latch rear hatch cover. 23. Move on around to the right front of the truck, drop the air cleaner pans to remove dirt, latch up and secure. Inspect battery box cover for damage and be sure it is in place and secure. 24. As you move in front of the radiator, inspect for any debris that might be stuck in front of the radiator and remove it. Check for any coolant leaks.
Inspect all head and fog lights. 14. While standing in front of rear hatch, look up to see that rear lights are in good condition, along with dual back up horns. Look up at panhard rod to see that it is getting proper greasing. Also look at both body hinge pins for greasing and any abnormal condition. 25. Before climbing ladder to first level, be sure ground level engine shutdown switch is ON. Inspect fire control actuator to be sure safety pin is in place and plastic tie that prevents acci- dental actuation is in place and in good condi- tion. Be sure battery disconnect switches are ON. 15. Perform the same inspection on the right rear suspension as done on the left. 16.
Move on around the right dual tires, inspect between the tires for rocks, and for condition of the rock ejector, inspect the tires for cuts or damage, and for correct inflation. 26. Climb ladder to main deck. Always use grab rails and ladder when mounting or dismounting from the truck. Clean ladder and hand rails of any foreign material, such as ice, snow, oil or mud. 17. Perform the same inspection for wheel lugs/ wedges, wheel cover latches, and for leaks that was done on the left hand dual wheels. 18. Move in front of right dual tires, and inspect the hoist cylinder the same as was done on the left side. Check security and condition of body-up