Caterpillar KENR5613-02 — инструкция

Features

INTERACTIVE SCHEMATIC Bookmarks X *This document is best viewed at a Options screen resolution of 1024 X 768. Features To set your screen resolution do the following: Cover Page RIGHT CLICK on the DESKTOP. Tables Component Select PROPERTIES. Connector CLICK the SETTINGS TAB. Schematic MOVE THE SLIDER under SCREEN RESOLUTION Machine Views until it shows 1024 X 768. Chassis View Cab View CLICK OK to apply the resolution. Engine View *Due to different monitor sizes and PDF reader preferences there may be some variance in linked schematic locations he Bookmarks panel will allow you to quickly navigate to points of interest.

Click here to save a copy of EC-C2 E-C60 this interactive schematic EC-C3 to your desktop E-C61 VIEW ALL CALLOUTS EC-C1 When only one callout is showing on a machine view, clicking on this button will Click on any text that is BLUE and make all of the callouts visible. This underlined. These are hyperlinks button is located in the top right corner that can be used to navigate the of every machine view page. schematic and machine views.

HOTKEYS (Keyboard Shortcuts) ELECTRICAL SYMBOLS BASIC HYDRAULIC COMPONENT SYMBOLS T FUNCTION KEYS P Sre ws is tcu hre Tem Sp we itr ca hture SL we iv te cl h SF wlo itw ch Circuit Breaker orP Mum otp or Variability Click here to view the Zoom In “CTRL” / “+” Schematic Symbols ConF dlu iti id oner (AdS jup sri tn ag ble) and Definitions page Zoom Out “CTRL” / “-” Fit to Page “CTRL” / “0” (zero) Hand Tool “SPACEBAR” (hold down) Find “CTRL” / “F” Zoom In “CTRL” / “+” Zoom Out “CTRL” / “-” Fit to Page “CTRL” / “0” (zero) Hand Tool “SPACEBAR” (hold down) Find “CTRL” / “F” ELECTRICAL SYMBOLS Pressure Switch T Temperature Switch Level Switch Flow Switch Circuit Breaker BASIC HYDRAULIC COMPONENT SYMBOLS Pump or Motor Variability Fluid Conditioner Spring (Adjustable)

Стр. 1

Features

SCHEMATIC SYMBOLS AND DEFINITIONS BASIC HYDRAULIC COMPONENT SYMBOLS Pump or Motor Variability Spring (Adjustable) Fluid Conditioner Spring Pressure Compensation ACCUMULATORS Control Valves Line Restriction (Variable) Spring Loaded Gas Charged Restriction Line Restriction (Fixed) PILOT CONTROL Line Restriction Variable and Pressure Compensated MAIN AUX. RELEASED PRESSURE 2-Section Pump External Return Internal Return Pump: Variable and Pressure Compensated REMOTE SUPPLY PRESSURE Attachment Simplified Hydraulic Pneumatic Energy Triangles HYDRAULIC SYMBOLS - ELECTRICAL Transducer (Fluid) BASIC ELECTRICAL COMPONENT SYMBOLS HARNESS AND WIRE SYMBOLS Fuse:

A component in an electrical circuit that will open the circuit if too much current flows through it. Wire, Cable, or Harness Assembly Identification: Includes Harness Identification Letters and Harness Connector Serialization Codes (see sample). Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The circle indicates that the component has screw terminals and a wire can be disconnected from it. AG-C4 111-7898 L-C12 3E-5179 Switch (Normally Closed): A switch that will open at a specified point (temp, press, etc.). No circle indicates that the wire cannot be disconnected from the component. Part Number: for Connector Plug 1 Ground (Wired):

This indicates that the component is connected to a grounded wire. The grounded wire is fastened to the machine. 2 Plug Receptacle Ground (Case): This indicates that the component does not have a wire connected to ground. It is grounded by being fastened to the machine. Harness Identification Letter(s): (A, B, C, AA, AB, AC, ...) Pin or Socket Number Reed Switch: A switch whose contacts are controlled by a magnet. A magnet closes the contacts of a normally open reed switch; it opens the contacts of a normally closed reed switch. Harness Connector Serialization Code: The "C" stands for "Connector" and the number indicates which connector in the harness (C1, C2, C3, ...) Sender:

A component that is used with a temperature or pressure gauge. The sender measures the temperature or pressure. Its resistance changes to give an indication to the gauge of the temperature or pressure. L-C12 3E-5179 T 5A Relay (Magnetic Switch): A relay is an electrical component that is activated by electricity. It has a coil that makes an electromagnet when current flows through it. The electromagnet can open or close the switch part of the relay. Fuse (5 Amps) 9X-1123 Component Part Number Harness identification code: This example indicates wire group 325, wire 135 in harness "AG". 325-AG135 PK-14 Solenoid: A solenoid is an electrical component that is activated by electricity.

It has a coil that makes an electromagnet when current flows through it. The electromagnet can open or close a valve or move a piece of metal that can do work. Wire Color Wire Gauge 1 2 Deutsch connector: Typical representation of a Deutsch connector. The plug contains all sockets and the receptacle contains all pins. Magnetic Latch Solenoid: An electrical component that is activated by electricity and held latched by a permanent magnet. It has two coils (latch and unlatch) that make electromagnet when current flows through them. It also has an internal switch that places the latch coil circuit open at the time the coil latches. 1 Sure-Seal connector:

Typical representation of a Sure-Seal connector. The plug and receptacle contain both pins and sockets.

2 VALVES ENVELOPES One Positi on Two Position Three Position PORTS Two-way Three-Way Four-Way CONTROL A B A B P T tion Shifted Position Infinite Position P T ormal Posi CHECK Basic Symbol Spring Loaded Shuttle Pilot Controlled INTERNAL PASSAGEWAYS FLOW IN ONE FLO DIRECTION EIT Infinite Positioning W ALLOWED IN HER DIRECTION Two Position PARALLEL CROSS FLOW FLOW Three Position PUMPS FIXED DISPLACEMENT Unidirectional Bidirectional VARIABLE DISPLACEMENT NON- COMPENSATED Unidirectional Bidirectional CYLINDERS Single Acting Double Acting MOTORS FIXED DISPLACEMENT Unidirectional Bidirectional VARIABLE DISPLACEMENT NON- COMPENSATED Unidirectional Bidirectional ROTATING SHAFTS Unidirectional Bidirectional Complete Internal Supply Pressur COMBINATION CONTROLS olenoid Solenoid or Manual Solenoid and Pilot Solenoid and Pilot or Manual Servo Thermal Detent LINES Crossing Joining MEASUREMENT Pressure Temperature Flow MANUAL CONTROL Push-pull Lever Manual Shutoff General Manual Push Button Pedal Spring FLUID STORAGE RESERVOIRS Vented Pressurized Return Above Fluid Level Return Below Fluid Level ELECTRICAL SYMBOLS Pressure Switch T Temperature Switch Level Switch Flow Switch Circuit Breaker er Transducer (Gas / Air) G Generator M Electric Motor Pressure Switch Pressure Switch (Adjustable) Electrical Wire Temperature Switch

Стр. 2

Components

KENR5613-02 February 2014 D7E Track-Type Tractor Electrical System TJA1-UP TAN1-UP Volume 1 of 2: Engine & Chassis Volume 2 of 2: Cab © 2014 Caterpillar, All Rights Reserved Printed in U.S.A.

Стр. 3

Engine and Chassis

Volume 1 of 2 - ENGINE and CHASSIS COMPONENT LOCATION Volume 1 - Component Location Component Schematic Location Machine Location Component Schematic Location Machine Location Actuator - ARD Air Flow Control E-4 1 Sensor - Fuel Pressure Filter (Before) F-1 72 Alarm - Backup H-16 2 Sensor - Fuel Rail Pressure H-2 73 Batteries A-15 3 Sensor - Fuel Temperature G-1 74 Block - Junction B-16 4 Sensor - Generator Speed Sensor #1 D-6 75 Coil - ARD Ignition D-3 5 Sensor - Generator Speed Sensor #2 D-6 76 Compressor - HVAC J-16 6 Sensor - Hydraulic Oil Temperature J-9 77 Control - Coolant Pump A-8 7 Sensor - Hydraulic Pump Oil Pressure C-6 78 Control - Engine H-5 8 Sensor - Intake Manifold Air Temperature G-2 80 Control - Generator F-15 9 Sensor - Motor ECM Drive Motor Speed #1 J-13 81 Control - Motor H-15 10 Sensor - Motor ECM Drive Motor Speed #2 J-13 82 Controller - ARD Air Flow E-3 11 Sensor - NOx Differential Pressure G-2 83 Converter - Accessory Power B-13 12 Sensor - NOx Intake Pressure G-2 84 Ground - CEM B-3 13 Sensor - NOx Temperature G-2 85 Ground - Chassis (Starter Motor) I-5 14 Sensor - Powertrain Lube Pressure J-12 86 Ground - Coolant Pump D-3 15 Sensor - PTO Tank Temperature C-6 87 Ground - Engine I-6 16 Sensor - Soot C-5 88 Ground - Frame #1 I-16 18 Sensor - Steering Charge Pressure C-6 89 Ground - Frame #2 A-10 19 Sensor - Steering Motor Speed I-13 90 Ground - Frame #3 A-10 20 Sensor - Turbo Inlet Air Pressure J-4 91 Ground - Frame (Disconnect Switch) I-8 21 Solenoid - ARD Fuel Flow Diverter Actuator F-1 94 Ground - Frame (Power Invertor) E-12 22 Solenoid - ARD Fuel Press.

Ctrl Act. #1 (Pilot) D-3 95 Ground - Front Chassis A-8 23 Solenoid - ARD Fuel Press. Ctrl Act.

#2 (Main) D-3 96 Ground - Fuel Tank A-13 24 Solenoid - Blade (Lower) C-2 97 Ground - Generator Stator I-6 25 Solenoid - Blade (Raise) C-2 98 Ground - Tilt Frame A-12 26 Solenoid - Brake Pressure Modulation I-13 99 Heater - ARD Fuel Nozzle D-4 27 Solenoid - Engine Cooling Fan C-6 100 Horn - High D-2 28 Solenoid - Fuel Pump #1 H-2 101 Horn - Low D-2 29 Solenoid - Fuel Pump #2 H-2 102 Invertor - Power G-13 30 Solenoid - Implement Lockout J-9 103 Module - Aftertreatment E-3 31 Solenoid - Injectors# 1-6 J-1 104 Module - Electric Drive Propulson Module H-11 32 Solenoid - NOx Flow Balance Valve Actuator G-2 105 Motor - ARD Fuel Pump F-1 33 Solenoid - NOx Valve Actuator H-2 106 Motor - Starter I-5 34 Solenoid - Parking Brake I-13 107 Motor - Washer (LH) C-13 35 Solenoid - Reversing Fan B-2 108 Motor - Washer (Rear) C-13 36 Solenoid - Service Brake I-13 109 Motor - Washer (RH) B-13 37 Solenoid - Start Aid J-4 110 Motor - Water Jacket Pump A-8 38 Solenoid - Steering Pump (LH) C-6 111 Probe - TDC Service J-2 39 Solenoid - Steering Pump (RH) C-6 112 Relay - ARD Fuel Nozzle Heater C-3 46 Solenoid - Tilt (Left) C-2 113 Resistor - Terminating (Engine) C-5 47 Solenoid - Tilt (Right) C-2 114 Resistor - Terminating (J1939) G-2 48 Solenoid - Tilt Cylinder Extend (Left) B-2 115 Resistor - Terminating A2 J-4 49 Solenoid - Tilt Cylinder Retract (Left) B-2 116 Resistor - Terminating B1 G-8 50 Stator - Generator I-6 117 Resistor - Terminating B2 B-2 51 Switch - Auxiliary Disconnect B-14 118 Resistor - Terminating D1 B-2 52 Switch - Disconnect J-8 119 Resistor - Terminating D2 G-8 53 Switch - Hydraulic Filter Bypass J-9 120 Resistor - Terminating F2 I-15 210 Switch - Underhood Worklamp J-4 121 Sensor - Aftertreatment 1 Sec Air Pressure C-3 92 Switch - Ingress Lighting J-9 122 Sensor - Aftertreatment Intake E-3 54 Switch - Remote Shutdown I-9 123 Sensor - Air Inlet Temperature J-4 55 Rear Implement Valve Sensor - ARD Fuel Pressure #1 (Pilot) D-3 56 Solenoid - 3rd Function Valve Port A B-14 124 Sensor - ARD Fuel Pressure #2 (Main) D-3 57 Solenoid - 3rd Function Valve Port B B-14 125 Sensor - Auxiliary Temperature D-15 93 Solenoid - Ripper Lower C-14 126 Sensor - Barometric Pressure H-2 58 Solenoid - Ripper Raise C-14 127 Sensor - Charge Air Cool Out Temperature G-2 59 Solenoid - Ripper Shank In C-14 128 Sensor - Coolant Temperature G-2 60 Solenoid - Ripper Shank Out C-14 129 Sensor - Crankcase Pressure H-2 61 Ripper Valve Sensor - Delta Pressure C-3 62 Solenoid - Ripper Lower (Ripper) D-14 130 Sensor - DPF Intake Pressure C-3 63 Solenoid - Ripper Raise (Ripper) D-14 131 Sensor - Drive Motor Winding Temperature #1 I-11 64 Solenoid - Ripper Shank In (Ripper) D-14 132 Sensor - Drive Motor Winding Temperature #2 I-11 65 Solenoid - Ripper Shank Out (Ripper) C-14 133 Sensor - Engine Oil Pressure H-2 66 Winch Valve Sensor - Engine Speed E-6 67 Solenoid - Drum Release D-13 134 Sensor - Engine Speed Timing A (CAM) F-3 68 Solenoid - Winch In D-13 135 Sensor - Engine Speed Timing B (CRANK) F-3 69 Solenoid - Winch Low Speed Lock C-13 136 Sensor - Fuel Level D-15 70 Solenoid - Winch Out D-13 137 Sensor - Fuel Pressure Filter (After) F-1 71

Стр. 4