15 ENGINE REF NO. PART NUMBER QTY DESCRIPTION REMARKS 2. 106-390 3 WASHER (M10) 1. 194-468 1 EXHAUST ELBOW (4" DIA.) 3. 153-340 1 HYDRAULIC PUMP 149-939 1 FILTER ELEMENT 4. 150-2180 1 HYDRAULIC PUMP LS SEE FOOTNOTE 2 190-1371 - PUMP SEAL KIT 5. 336-051 1 FLY WHEEL HOUSING COVER 6. 160-897 1 DRIVE COUPLING 7. 194-662 1 ENGINE-CUMMINS QSB6.7 SEE FOOTNOTE 1 500-1411 - FUEL FILTER HEAD 195-1034 - FILTER, ENGINE OIL 195-1035 - FUEL FILTER (PRIMARY) 195-1036 - FUEL FILTER (SECONDARY) 195-1074 - OIL FILL CAP 195-1075 - OIL DIP STICK 195-1076 - BELT 195-1077 - THERMOSTAT 195-1078 - ALT 9. 105-456 2 BOLT (5/8-NC X 1-3/4", GD8) 8. 106-398 2 WASHER (M16, HARDENED) LOCTITE 242 10. 195-1496 1 MUFFLER 11.
105-244 4 WASHER (1/2") 12. 105-048 4 BOLT (1/2-NC X 1-1/2") 13. 106-383 12 FLG LK SCREW (M10-1.50 X 30mm) 14. 105-156 8 BOLT (3/8-NC X 1-1/2") USE 242 LOCTITE USE 242 LOCTITE 15. 105-072 8 LOCK WASHER (3/8") 16. 110-333 3 BOLT-ON CLAMP (1") 17. 157-084 - O-RING (159 D70) SEE FOOTNOTE 3 USE 242 LOCTITE, TORQUE TO 30 FT LBS 18. 194-027 2 MUFFLER CLAMP 19. 194-876 1 EXHAUST ADAPTER 20. 300-2421 1 BAND 21. 106-332 1 SCREW (M10-1.50 X 70mm) 22. 106-758 1 LK NUT (M10-1.5) 23. 300-2450 1 SUPPORT BRACKET 24. 106-558 2 CLIP NUT (M10-1.5) 25. 106-164 2 FLG SCREW (M10-1.50 X 30mm) 26. 300-2409 1 SUPPORT 27. 106-382 2 FLG SCREW (M10-1.50 X 20mm) 28. 105-245 1 SCREW (M10-1.50 X 25mm) 29.
110-333 1 BOLT-ON CLAMP (1") 30. 194-049 1 CLAMP ASSEMBLY 31. 110-373 1 BOLT-ON CLAMP (13/16") 32. 105-095 1 WASHER (1/4") 33. 106-080 2 SCREW (M10*1.50 X 20MM, SOC) FOOTNOTES: 1. TORQUE CROSSBOLT TO 85-90 FT LB; MOUNT FLUSH WITH END OF SHAFT 2. ON THE BACK OF THE PUMP OF SOME EARLY MACHINES A DIFFERENT MOUNT PAD WAS USED. IF THE BOLTS HOLDING THE PAD TO THE PUMP HAVE A WASHER UNDER THE BOLT HEAD USE O-RING 157-201 BETWEEN THE PUMPS. 3. SET ADAPTER 1.0" FROM 90° BEND IN ELBOW NOTE: REFER TO O-RING CHART (800-301) IN BACK OF THE BOOK FOR REPLACEMENT OF O-RINGS. 11 ID0145574