CONTENTS SECTION 20 CONTENTS 1. DIAGNOSIS TOOLS “ALL ROUND TESTER .................... 1 4.3.3 CALIBRATION OF THE MAIN CLUTCH PROPORTIONAL SOLENOID VALVE........................29 1.1 ALL ROUND TESTER ......................................................... 1 1.1.1 DESCRIPTION OF THE KIT....................................... 1 1.1.2 NOTES ON CORRECT USE ...................................... 2 1.1.3 DESCRIPTION OF THE TESTER............................... 2 1.1.4 GENERAL NOTES ON CONNECTING AND POWERING UP THE TESTER ................................... 3 1.1.5 SELECTION OF THE DISPLAY LANGUAGE ............. 3 1.1.6 SETTING THE SERIAL PORTS..................................
5 4.4 RENEWAL OF HYDRAULIC LIFT AND ASM CONTROL UNIT ................................................................31 4.4.1 PROGRAMMING THE TYPE OF TRACTOR............. 32 4.4.2 CONFIGURING NO RADAR STATUS ...................... 33 4.4.3 CALIBRATION OF THE LIFT POSITION SENSOR................................................................... 34 4.4.4 CHECKING AND CALIBRATING THE LIFT CONTROL LEVER 36 1.2 “SERDIA 3.5 LEVEL III” SOFTWARE .................................. 7 1.2.1 DESCRIPTION OF THE KIT....................................... 7 1.3 “EDS EST45” SOFTWARE ................................................. 8 1.3.1 DESCRIPTION OF THE KIT.......................................
8 4.5 RENEWAL OF THE INFOCENTER ....................................39 4.5.1 ENTERING CONSTANTS......................................... 39 4.6 RENEWAL OF AXLE SUSPENSION CONTROL UNIT ......41 4.6.1 CHECKING CALIBRATION OF THE SUSPENSION POSITION SENSOR 41 2. CONNECTING THE TESTER TO THE ELECTRONIC CONTROL UNITS .............................................................. 9 2.1 CONNECTING THE ART TO THE HYDRAULIC LIFT AND FRONT AXLE SUSPENSION CONTROL UNITS ................ 9 5. ALARMS .......................................................................... 43 5.1 LIFT AND ASM CONTROL UNIT ALARMS .......................43 5.1.1 LIST OF ALARMS BY EXTENDED CODE ................
44 5.1.2 LIST OF ALARMS BY STANDARD CODE................ 46 5.1.3 LIST OF ALARMS DISPLAYED ON ART.................. 48 5.1.4 ANALYSIS OF LIFT AND ASM ALARMS.................. 50 2.2 CONNECTING THE PORTABLE COMPUTER WITH “SERDIA 3.5” SOFTWARE TO THE ENGINE CONTROL UNIT ................................................................................. 10 2.3 CONNECTING THE PORTABLE COMPUTER WITH “EDS” SOFTWARE TO THE TRANSMISSION CONTROL UNIT AND INFOCENTER............................................................ 11 2.3.1 CONNECTION TO THE TRANSMISSION CONTROL UNIT 11 2.3.2 CONNECTION TO THE INFOCENTER....................
11 5.2 LIST OF TRANSMISSION CONTROL UNIT ALARMS .......79 5.2.1 ABNORMALITIES NOT DETECTED BY THE TRANSMISSION CONTROL UNIT 79 5.2.2 ALARMS INDICATED ON THE TRANSMISSION DISPLAY AND BY THE EDS PROGRAM 79 5.2.3 DEFINITION OF TRANSMISSION OPERATING MODES 83 5.2.4 ANALYSIS OF ALARMS........................................... 84 3. INTRODUCTION TO THE ELECTRONIC SYSTEM OF THE TRACTOR .......................................................... 13 3.1 ENGINE CONTROL UNIT (DEUTZ EMR2) ........................ 13 3.2 TRANSMISSION CONTROL UNIT ...................................
15 5.3 LIST OF ALARMS DISPLAYED BY SERDIA ....................139 5.3.1 ALARMS DISPLAYED USING THE SERDIA PROGRAM 139 5.3.2 ANALYSIS OF ALARMS......................................... 141 3.3 POWER LIFT CONTROL UNIT ......................................... 16 3.3.1 HYDRAULIC LIFT SYSTEM..................................... 16 3.3.2 ASM SYSTEM.......................................................... 17 5.4 LIST OF FRONT AXLE SUSPENSION CONTROL VALVE ALARMS ..............................................................161 5.4.1 LIST OF ALARMS BY TEXT CODE ........................ 161 5.4.2 LIST OF ALARMS BY STANDARD CODE..............
162 5.4.3 LIST OF ALARMS DISPLAYED BY ART................. 163 5.4.4 ANALYSIS OF ALARMS......................................... 164 3.4 INFOCENTER 2 or 3 ......................................................... 18 3.5 FRONT AXLE SUSPENSION CONTROL UNIT ................. 19 3.6 FRONT AND REAR PTO CONTROL UNIT ....................... 20 4. PUTTING THE TRACTOR INTO SERVICE .................... 21 4.1 INTRODUCTION ............................................................... 21 6. OPERATOR’S MANUAL EDS (Electronic Diagnosis System) .................................... 177 4.2 RENEWAL OF THE ENGINE CONTROL UNIT .................
21 4.2.1 READING AND SAVING DATA ................................ 21 4.2.2 PROGRAMMING THE CONTROL UNIT.................. 22 4.2.3 CALIBRATION OF THE ACCELERATOR PEDAL .... 23 4.2.4 CALIBRATION OF THE HAND THROTTLE ............. 24 1. GENERAL INTRODUCTION ............................................177 1.1 FUNCTIONAL SCOPE............................................ 177 1.2 HARDWARE REQUIREMENTS .............................. 178 1.3 STARTING AND TERMINATING OF THE EDS PROGRAM 180 4.3 RENEWAL OF THE TRANSMISSION CONTROL UNIT .... 25 4.3.1 SETTING THE TRACTOR VERSION AND SERIAL NUMBER ..................................................................
25 4.3.2 CALIBRATION OF THE CLUTCH PEDAL POSITION SENSOR ................................................. 27 2. TRANSMISSION DIAGNOSIS .........................................182 2.1 THE MAIN MENU ................................................... 182 2.2 ONLINE HELP ........................................................ 184 20-i