Supermicro BPN-SAS-818TQ Backplane User & Service Manual PDF (EN)

BPN-SAS-818TQ Backplane JP51 J6 #2 J35 R S UPER LED TEST J10 J9 +12V GND +5V +12V GND +5V #1 J7 UPGRADE JP46 RESET J29 J8 #0 J8 SIDEBAND JP10 +12V GND GND +5V REV 1.02 BPN-SAS-818TQ USER'S GUIDE REV. 1.0c

Стр. 1

Safety Information and Technical Specifications BPN-SAS-818TQ Backplane User’s Guide Table of Contents The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Contacting Supermicro.......................................................................................iv Super Micro Computer, Inc.

("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent. Chapter 1 Guidelines Returning Merchandise for Service.....................................................................v 1-1 ESD Safety Guidelines....................................................................................

1-1 IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. 1-2 General Safety Guidelines...............................................................................

1-1 1-3 Version Information.......................................................................................... 1-2 Chapter 2 Connectors, Jumpers and LEDs 2-1 Rear Connector Locations............................................................................... 2-1 Rear Connectors.............................................................................................. 2-1 Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes.

Super Micro's total liability for all claims will not exceed the price paid for the hardware product. 2-2 Rear Connector and Pin Definitions................................................................ 2-2 2-3 Rear Jumper Locations and Pin Definitions.................................................... 2-4 Explanation of Jumpers................................................................................... 2-4 FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense. 2-4 Front Connectors and LED Indicators.............................................................

2-5 Front Connector Locations.............................................................................. 2-5 Front Connector/LED Indicator Descriptions................................................... 2-5 California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate” WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.

Manual Revision 1.0c Release Date: January 20, 2017 Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright © 2017 by Super Micro Computer, Inc. All rights reserved. Printed in the United States of America ii iii

Стр. 2

Returning Merchandise for Service

Safety Information and Technical Specifications BPN-SAS-818TQ Backplane User’s Guide Contacting Supermicro Returning Merchandise for Service Headquarters A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered. You can obtain service by calling your vendor for a Returned Merchandise Authorization (RMA) number. When returning to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling charges will be applied for all orders that must be mailed when service is complete. Address: Super Micro Computer, Inc. 980 Rock Ave.

San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) For faster service, RMA authorizations may be requested online (http://www. supermicro.com/support/rma/). support@supermicro.com (Technical Support) Whenever possible, repack the backplane in the original Supermicro box, using the original packaging materials. If these are no longer available, be sure to pack the backplane in an anti-static bag and inside the box. Make sure that there is enough packaging material surrounding the backplane so that it does not become damaged during shipping. Website: www.supermicro.com Europe Address: Super Micro Computer B.V.

This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration, misuse, abuse or improper maintenance of products. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390 During the warranty period, contact your distributor first for any product problems. Fax: +31 (0) 73-6416525 Email: sales@supermicro.nl (General Information) support@supermicro.nl (Technical Support) Website: www.supermicro.nl rma@supermicro.nl (Customer Support) Asia-Pacific Address: Super Micro Computer, Inc. 3F, No. 150, Jian 1st Rd. Zhonghe Dist., New Taipei City 235 Tel: +886-(2) 8226-3990 Taiwan (R.O.C) Fax:

+886-(2) 8226-3992 Email: support@supermicro.com.tw Website: www.supermicro.com.tw iv v

Стр. 3

Returning Merchandise for Service

BPN-SAS-818TQ Backplane User’s Guide Notes vi

Стр. 4