CW-C6000 Series / CW-C6500 Series External I/O Technical Reference Guide (EN)

Series Series External I/O Technical Reference Guide Overview External I/O Specification Commands Printer Statuses and Signals Timing Extended I/F Signal Operation Mode Settings Appendix M00123704 Rev.E

Стр. 1

Cautions No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permis- sion of Seiko Epson Corporation. The contents of this document are subject to change without notice. Please contact us for the latest informa- tion. While every precaution has been taken in the preparation of this document, Seiko Epson Corporation assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third par- ties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Seiko Epson Corporation. Trademarks Product names used herein are for identification purposes only and may be trademarks of their respective own- ers. ©Seiko Epson Corporation 2019–2024 2

Стр. 2

Manual Content

Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc.; or func- tional/precision devices etc., you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability.

Because this product was not intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care etc., please make your own judgment on this product’s suitability after a full evaluation. 3 About this Manual Aim of the Manual This manual was created to provide information on development, design, and installation of systems and devel- opment and design of printer applications for developers. Manual Content The manual is made up of the following sections:

Chapter 1 Overview Chapter 2 External I/O Specification Chapter 3 Commands Chapter 4 Printer Statuses and Signals Chapter 5 Timing Chapter 6 Extended I/F Signal Operation Mode Settings Chapter 7 Appendix

Стр. 3

Safety Precautions on Handling

Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. 4 WARNING You must follow warnings carefully to avoid serious bodily injury. CAUTION Provides information that must be observed to prevent damage to the equipment or loss of data. • Possibility of sustaining physical injuries. • Possibility of causing physical damage. • Possibility of causing information loss. c IMPORTANT Indicates information with which you must comply when using the product. Mishandling due to ignoring this information may cause the product to fail or malfunction.

Q NOTE Indicates supplementary explanations and information you should know. Safety Precautions on Handling WARNING • Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire or electric shock. Immediately unplug the equipment. • Only disassemble this product as described in this manual. Do not make modifications to the unit. Tampering with this product may result in injury, fire, or electric shock. • Never insert or disconnect the power plug with wet hands. Doing so may result in severe shock. • Do not allow foreign matter to fall into the equipment. Penetration by foreign objects may lead to fire or shock.

• If water or other liquid spills into this equipment, unplug the power cord immediately. Con- tinued usage may lead to fire or shock. • Handle the power cord with care. Improper handling may lead to fire or shock. ∗ Do not modify or attempt to repair the cord. ∗ Do not place any object on top of the cord. ∗ Avoid excessive bending, twisting, and pulling. ∗ Do not place cord near heating equipment. ∗ Check that the plug is clean before plugging it in. ∗ Be sure to push the prongs all the way in. • Be sure to set this equipment on a firm, stable, horizontal surface. Product may break or cause injury if it falls. • Do not use in locations subject to high humidity or dust levels.

Excessive humidity and dust may cause equipment damage, fire, or shock. • Do not place heavy objects on top of this product. Never stand or lean on this prod- uct.Equipment may fall or collapse, causing breakage and possible injury.

Стр. 4