US Army Materiel Command AMCP 706-250 — AMCP 706-250 Guns—General Engineering Design Handbook (1964) PDF (EN)

Downloaded from https://www.everyspec.com a gear sector connected by rod to the cam-oscillated arm on the right side of the transmission case. presses the rammer spring. The next cartridge is meanwhile fed downward into the tray, its rim resting in the grooves of the rammer levers. As the tray terminates its forward motion, it trips the rammer catch lever and the rammer spring drives the rammer rod forward, pulling the shoe, levers and cartridge. When the rammer shoe nears its forward limit of travel, the cam slots swing the ramming levers outward sufficiently to release the cartridge, which is carried into the chamber by its own momentum. 3-8.1.2.6.

Automatic Loader for Clipped Ammunition (see Figure 3-23) For drop block cannon of relatively small bore diameter using fixed ammunition in clips, current practice is represented by an automatic feeding and loading device, operated by movement of the gun in recoil and counterrecoil and by action of a spring compressed during counterrecoil. The mechanism receives the cartridge in clips, disengages the car- tridges from the clips, ejects the clips, feeds one cartridge at a time downward to a loading tray affixed to the gun breech ring, and rams the car- tridge into the chamber after counterrecoil, thereby tripping the extractor to effect the closing of the breech.

A hand lever and suitable linkage are provided for manual operation of the rammer to initiate the automatic cycle or for single-shot opera- tion when desired. (c) Feeding Mechanism The feeding device, which serves also as a small- capacity magazine, is supported in the nonrecoiling breeeh casing above the tray and rammer. Front, and rear frame members are channeled to guide the nose and base of the cartridge downward into the tray in proper position, with the rim of the base entering the slots in the levers of the cocked ram- mer shoe.

Right aHd left side frame channels house the upper portions of the reciprocating feed rods, which carry spring-loaded pawls to pull the car- tridges downward as the cam grooves of the tray, in engagement with the lower ends of the rods, force the rods downward. Also in the side frames are fixed pivot pawls to hold the cartridges down- ward while the feed rods return to upper position. The rear frame member incorporates a cam that disengages the hooks of the cartridge clip from the rim of successive cartridges as the latter are pushed down and deflects the freed clip into an ejection chute.

The lower end of the feed mechanism, just above the rammer tray, incorporates two parallel, longitudinally disposed feed rollers, each having four cylindrically concave sides. The space be- tween rollers is such as to permit one cartridge at a time to pass downward between them onto the tray, by rotation of the rollers toward each other through 90 degrees. An interlocked catch system limits roller rotation to one such quarter-turn in each recoil cycle of the gun and to that period when the feed rods are pulling the stack of car- tridges downward. (a) Loading Tray The tray is a trough rigidly attached to the breech ring in alignment with the gun bore.

The tray sides incorporate cam grooves that impart a vertical reciprocating motion to ammunition feed rods as the tray moves with the gun in recoil and counterrecoil. Each side of the tray features also a cam slot for guidance of the two rammer levers that are supported in the rammer shoe and extend through the slots to clasp and drive the cartridge forward during the ramming motion of the shoe.

(b) Rammer The principal parts of the rammer, contained within the housing in the under side of the tray, are a rod and helical spring, a shoe attached to the rear end of the rod and slidably supported in longitudinal grooves in downward-extending side flanges of the tray, and the two rammer levers, which are pivoted in the shoe and extend upward through the cam slots in the sides of the tray to clasp the rear end of the cartridge with a tong action. The upper ends of the levers are grooved for straddling engagement of the cartridge rim. AH the gun recoils, the rammer is carried rearward by the tray.

As the gun counterrecoils, the rammer shoe is retained in the rearward position by a catch lever mounted on the stationary breech hous- ing. The forward movement of the tray then com- 3-8.2 Small Arms Feeding Methods 3-8.2.1 Manual Feeding Because of the growing demand for increased rates of firing, the simple manual method of placing each successive round in the receiver, in position 3—24