Downloaded from https://www.everyspec.com 3-8.2.2.4 Clip Feeding belt, extracts the cartridges and feeds them suc- cessively into the gun receiver in front of the •re- tracted bolt, whence they are chambered by the M forward bolt movement. The feed mechanism may ^ be powered by gun recoil of by a separate power source. The clip method of feeding, exemplified by the U. S. Rifle, Cal. .30, Ml, presents a compromise between the wholly integral and the separate unit magazine. The clip compromises a thin spring- steel casing bent to a flat-based U, forming (as in- serted in the gun) two sides and rear wall, all vertical.
The free forward edges of the sides press inward to clasp the sides of two vertical columns of four horizontal cartridges each, staggered, with bases against the rear of the clip. The cartridges project from the open front and are retained at top and bottom by inwardly curved lips on the sides. The loaded clip is inserted downward through the top of the gun receiver into a recess in the lower part of the receiver, depressing the spring-loaded follower within the recess. The fol- lower presses upward on the group of cartridges so that each time the bolt moves rearward suffi- ciently to clear, the topmost cartridge is moved upward into the mouth of the clip.
In its subse- quent forward movement, the bolt then pushes this top cartridge forward lengthwise between the lips of the clip until free of the clip and on into the chamber. When the last cartridge of the clip has been fired the empty clip is ejected on completion of the rearward travel of the bolt. 3-8.2.3.1 Fabric Belts Practical use of a fabric belt necessitates a mecha- nism that will withdraw the cartridge rearward from the belt then move the round at right angles to its axis to clear the belt and align with the cham- ber prior to ramming action by the bolt.
In a typical mechanism, the movement of the belt cen- ters the incoming cartridge over the closed bolt, with the base groove of the case engaged under a hooked extractor lever mounted on the bolt. As the bolt moves rearward, the extractor pulls the cartridge from the belt then is cammed downward to push the cartridge base into a vertical tee slot in the front face of the bolt. In the same bolt movement, the fired case, with its base engaged lower in the tee slot, is withdrawn from the cham- ber.
As the bolt returns forward the extractor is cammed downward further to push the live car- tridge down to alignment with the chamber, dis place the fired case and eject it from the bottom of the tee slot. 3-8.2.3 Belt Feeding I 3-8.2.3.2 Metallic Belts For continuous feeding of a greater number of cartridges than can be contained in a magazine of practical size, a belt system is used. Belts are usually made either of fabric or of metal.
The belt consists of two layers of fabric strip stitched together transversely at intervals to form a suc- cession of loops to carry cartridges parallel to each other and at right angles to the length of the belt or of a succession of articulated metal links formed for transverse insertion of cartridges to provide a chain of rounds of the desired length. In a typical application the belt is mechanically fed through the gun receiver, where the cartridges are succes- sively extracted from the belt and pushed into the chamber by the reciprocating bolt.
Individual operations of belt feed and cartridge extraction from the belt are effected by lever and pawl mecha- nisms attached to, or actuated by the moving bolt. In a variation from this system, the belt is fed through a separate feeding mechanism attached to the gun receiver. The mechanism advances the Permanently linked metallic belts may be oper- rated in a manner similar to that indicated, for fabric belt.
However, by reducing the cartridge- holding loops to a C-shape with slightly more than a half-circle of grip, and disposing the loop open- ings on the side of the belt nearest the bolt, the bolt can be arranged to push the cartridge forward out of the loop and into the chamber in the coun- terrecoil movement of the bolt. This permits de- sirable simplification of the mechanism and action. The open-side loop also permits lateral removal of the cartridges from the belt, a method advanta- geous when used with a disintegrating belt.
The disintegrating belt is one in which each link, as its cartridge is removed, is disconnected from the following portion of the belt and is individually rejected through a suitable chute, while the car- tridge is guided into ramming position. In a typi- cal disintegrating belt, a cartridge functions as the hinge pin to provide an articulated joint between 3—26