US Army Materiel Command AMCP 706-250 — AMCP 706-250 Guns—General Engineering Design Handbook (1964) PDF (EN)

Downloaded from https://www.everyspec.com and depth of grooves roughly proportional to caliber. 4-4.2 Details of Contour and Function The pitch of the helical path of the rifling grooves, generally expressed as "one turn in (ap- plicable number) calibers," may be uniform through the bore length, or the rate of turn may be increased from a low value near the origin to the- required final value at or near the muzzle. The increasing twist, method reduces the rotational loading on the rear portion of the bore, which is subject to more severe erosive condition than is the portion nearer the muzzle.

However, increasing twist requires alteration of the angle of the en- graved grooves in the projectile as the projectile moves forward, and this limits the width of rotating band that may be used without undesirably in- creasing the force required to engrave the projec- tile. It also increases the rotation-accelerating forces to be applied by the rifling in the forward portion of the bore. U. S. Army design practice at present generally favors uniform twist in cannon and increasing twist in small arms guns (see also par. 3-4.3.2). Typical transition contours of breech-loading guns are shown in Fig. 3-1. Their designations and functions are as follows:

4-4.2.1 Forcing Cone (1) This tapered section, immediately back of the bore, is designed to accomplish a centered, gas- sealing entrance of the rearward section of the projectile jacket or band into the main bore, by forcing a slight reduction in diameter as that sec- tion of the projectile enters the bore. In loaded position the fit is sufficiently snug to provide an initial seal, except in some small arms using bullets designed to be expanded to sealing diameter by initial pressure of the propellant.

In cannon using separate loading ammunition, the taper must be gradual enough to retain the rammed projectile in proper firing position as any angle of gun elevation at which the weapon may be fired. (2) For rifled bores (except recoilless rifles) the forcing cone effects a distribution of the work of engraving the projectile (or its rotating band) over an appreciable' length of projectile travel, thereby reducing 'the propellant pressure required for initial movement of the projectile. 4-4 Transition Region This region comprises the forward portion of the chamber, from the rear of the chamber front slope (see Pig. 3-1) through the forcing cone.

(3) For recoilless rifles, the rotating bands of the projectiles are preengraved (grooved in manu- facture) to fit the rifling of the bore in order to minimize the propellant force required to start the projectile. The rotating band is inserted into the rifling in the loading operation. Hence, the forcing cone is replaced by an abrupt taper or shoulder at the origin of rifling, to facilitate the manual align- ment and insertion. The taper may be preceded by an aligning cylinder, which, in turn, may be preceded by a guiding taper.

4-4.1 General Contours and Functions The transition region consists of a series of ta- pered sections (one or more cylindrical sections may be included) connecting the forward section of the principal cavity of the chamber with the rear section of the main bore (rifled or smooth). The general functions of the contours are: (1) To center the projectile at the entrance to the main bore, so it may enter the bore in proper alignment, without undesired deformation, and with the uniformity of round-to-round resistance necessary to maintain uniform development of propellant pressure and resultant muzzle velocity.

4-4.2.2 Bullet Seat This is a cylindical section immediately back of the forcing cone in small arms weapons, serving to support the bullet centrally at the entrance to the forcing cone. (2) To provide for such seating of the pro- jectile, in loading, as will prevent leakage of pro- pellant gases past the projectile into the bore before the projectile has completed its entry into the bore under propellant pressure. 4-4.2.3 Band Cylinder This cylindrical section, a feature of some sepa- rate loading cannon, supports the rear of the pro- jectile rotating band in central position while the