US Army Materiel Command AMCP 706-250 — AMCP 706-250 Guns—General Engineering Design Handbook (1964) PDF (EN)

Downloaded from https://www.everyspec.com 5-5.4.1 Voids produces what is termed secondary flash, of greater brillance than that indicated in (2) above. A device to aid the igniter charge or charges in effecting rapidity and uniformity of propellant ignition consists in the provision of voids within or around the propellant charge in the cartridge case or gun chamber. The unobstructed space permits the igniting flame to spread more freely to all portions of the propellant charge. (4) If unburned solid particles (notably car- bon) below ignition temperature are ejected with the propellant gases, smoke will be produced.

Par- ticles other than carbon may contribute to visible smoke or vapor, through visibility of the particles, or by ''reaction with the atmosphere to produce condensation of water vapor. Materials added to the propellant for combustion or erosion control and metal particles abraded from the gun bore or projectile are considered possible causes of the reaction. 5-5.4.2 Ignition As a Factor in Design The necessity for uniformity of ignition for uni- form round-to-round propellant action compels consideration of ignition requirements as well as propellant space requirements in coordination of the design of the gun chamber with the propellant charge design.

The determination of ammunition type having been made (i.e., fixed, semifixed, sepa- rated, or separate loading), the ammunition de- signer assumes the task of designing suitable pro- pellant and ignition elements, and specifying the necessary chamber volume. For optimum results, the gun designer must cooperate by providing, within the limits imposed by other gun design requirements, a chamber of adequate volume and sufficiently low length-to-diameter ratio to enable a satisfactory solution of the ignition problem. 5-6.2 Disadvantages Both smoke and flash are objectionable in that they reveal to the enemy the location of the weapon and operating personnel.

Further, smoke may ob- scure the operators' view of the target area imme- diately after firing and so reduce the effective use of the weapon. 5^6.3 Correlation With Grain, Form, Charge and Tube Design From the discussion in paragraph 5-6.1 it follows that the production of smoke or flash is affected by the form and dimensions of the propellant grains. Grains of degressive form produce their peak of temperature and pressure relatively quickly and, for a given energy yield within the gun, are re- duced to relatively lower temperature and pressure before exit from the muzzle.

This action presents a reduced tendency to flash, as compared to neutral and progressive forms (perforated types), which produce a lower and later peak of temperature and pressure, but show higher temperature and pressure at the muzzle for a given energy yield within the gun. 5-6 Smoke and Flash 5-6.1 Causes » Combustion of the propellant does not progress to completion in the gun tube or barrel. The available oxygen in the propellant is insufficient to complete the combustion reaction with all the re- maining elements. For example, the major portion of the carbon may be converted to carbon monox- ide, but not to carbon dioxide.

Depending on the quantity and characteristics of the propellant, the geometry of the gun tube, and size and weight of the projectile, various effects may be produced as the propellant gases emerge from the muzzle: The composition of the propellant charge will affect the production of flash or smoke through its effects on: total heat evolved; rate of combustion; temperature of flame produced; the proportion of nonburnable gases evolved; the quantity of non- burning solids (included for control of combustion rate, temperature, erosion, stability, or other pur- poses) and oxygen balance.

With the same gun interior, same projectile and same maximum pres- sure limit, increases in muzzle velocity necessitate persistence of near-maximum pressure and tem- perature into sections nearer the gun muzzle. This (1) If the initial combustion persists at emer- gence of the propellant, flash will result. (2) If gases are not cooled below incandes- cence before exit, flash will result. (3) If the products of incomplete combustion (notably hydrogen and carbon monoxide) are not below ignition temperature at emergence, contact with atmospheric oxygen will effect a renewal of combustion beyond the gun muzzle. This action