Downloaded from https://www.everyspec.com - STRUCTURES From Equation (3-12) K =-182 and substi- when the pressure reaches the following tation of the numerical values in Equation critical value: (3-18) yields h V7liv V= -1.99 x 10 = x 8.63 X i0- = p. 0.92E0-1 R(3- - - 17.2 lb per in Here r7 is Young's Modulus, h the wall th.ck- With M., = 0 the condition of a maximum ness, R the radius of the median surface of moment becomes the cyiinier, and L the length of the cylinder Kx R r 4 (3-19) between s, pports; Poisson's ratio v is taken Substitution in Equation (3-13) leads to -ps 0.3.
Thi- equation is valid only if M..x 0.322V.RK = 0.442V 0 0.763 , 7i 1 (3-23) - 7.6 in lb per in The meaning of this restriction should be The corresponding stress is from Equation understood from a numerical example. When (3-15) R = 25 in. ant' h g h in., the inequality Ob.= = 2920 psi reduces to 0.4321 1. If L = 10 in., the ;eft- From Equation (3-19) the iocation of the hand member is 4.32; with this value one can maximum bending stress is expect a reasonabit approximat.on. The ac- x (r, 4) (R/K) = 1.08 in. curacy increases wikh increasing L. which is very close to the juncture.
The at- For very long cyhirders the critical ,res- tenuation length is from Equation (3-16) sure is = R, K = 1.37 in. p,, =E 14(1 -- -2)]1(h,'RJ (, -24) Hence interference from the ton of the henii- Equation (,-24) is to b. used in preference sphere and from the other end o.7 the cylir der 'to Equation (3-22) when it predicts a higher is negligible and the results obtained are buckling pressure than Equation (3-22). accurate enough for engineering purposs. For very short cylinders which do not sat- Superposition of a, and of ah. yields the isfy inequality (3-23), the literature should maximum normal stress which acts in the be consulted.
- ' cylinder in the axial direction at a dista ice 3-4.2. Uniform Axiai Pressure. The buck- of 1.08 in. from the juncture on the outer ling stress under the application of a uniorm surface of the wall- axial pressure can be calculated florn the a .. ,.. = 10,000 + 2920 = 12,920 psi fomlI Finally a general forniula can be deriied where from Equations (3-13), (3-18) and (3-19' k = 9(h/R)0. + 0.16(R, L)'.(h R) 03 (3-25) which is valid when the cylinder and i he and h, R, and L are as defined in the previous equivalent cylinder have the same radius a id paragraph. For example, k = 0.24 when the same wall thickness: R/h -= 500 and R L =- 1. For short and com- M.= - 0.0465 -E h - AR%I - ARp,:
1 paratively thick-walled cylinders Equation R (3-25) yields values of k exceeding 0.3; it is (3-40) recommended that in such cases k should be When v' 0.3, this becomes taken as 0.3. M.,= - 0.0487Eh 2 ARI - ARph.... R (3-21) -4 T3-4.3. Pure Bending. It is customary to cal- CYLINDRICAL SHELLS culate the maximum bending stress in a cylindrical shell from the engineering theory 3-4.1. Uniform Lateral Pressure. If a uni- of bending.
If the maximum compressive form external pressure p is acting over the stress so found is less than 1.33 times the circular cylindrical surface of a shell, but Pot critical axial stress obtained from Equation X over the end sections, the cylinder hackles (3-24), the cylinder is riot expected to buckle. ( ', 414