US Army Materiel Command AMCP 706-117 — Environmental Series, Part Three: Induced Environmental Factors (EN)

F Downloaded from https://www.everyspec.com AMCP 700-117 The two main sources of pollutants in the area were Aluminum and stainless steels develop thin continu- chemical plants emitting a variety of substances, in- ous oxide films that provide protection to the underly- eluding gaseous sulfur compounds, and a nearby ing metal in all but the most severely polluted areas. municipal burning dump producing all the pollutants Copper develops a corrosion product film that retards associated with combustion, further attack.

However, ordinary carbon steels require The solution arrived at by the FAA was to install an some form of protection when exposed to atmospheric air-conditioning system with activated-charcoal filters, conditions. Protective methods available include coat- (2) Telephone switching equlpment-N, Y. Bell ing with a highly resistant metal such as zinc or alumi- Telephone Company. A New York Bell Telephone num, an epoxy or vinyl paint coating, and electroplat- Company's switching center, containing complex corn- ing with a chrome-nickel-copper combination.

The puter-controlled electronic switching networks and most common methods of protection for exposed struc- located close to a power generating station, experienced tures are galvanizing and painting or a combination of erratic computer behavior. Evaluation of the situation both (Ref. 51). by IBM engineers showed that outside particulate con- Since most of these preventive measures apply to tamination was the cause.

systems that are likely to be exposed to marine and high The installation of a high-efficiency air filter elimi- humidity environments as well as polluted environ- nated the computer malfunctions and decreased main- ments, it seems reasonable to assume that any equip- tenance for other switching equipment. ment designed to operate outdoors (e.g., vehicles, (3) Others. Many case histories of electronic com- weapon systems, etc.) will be operated in at least one ponents and systems that are affected by air pollutants of these highly corrosive environments during its life have been tabulated. They include examples of photo- chemical oxidants reacting to form an insoluble scum cycle.

or film on silicon wafers during processing, inoperative (2) Electronic systems Complex precision elec- electronic equipment such as FM tuners that only tronic systems, such as computers and switching net- needed cleaning to restore normal operation, and in- works, have been affected by high concentrations of creased rejection rates experienced by a manufacturer particulate matter and sulfur dioxide. The solution to of sensitive components when a freeway ramp was con- date has been to install air filtering and conditioning structed approximately 400 ft from the manufacturing systems in the building in which the equipment is building. located.

This does not mean that the equipment itself could not have been designed or redesigned to preclude the effects of air pollutants. For example, the equip- 2-8 PROTECTION AGAINST ment could be housed in an airtight container with a ATMOSPHERIC POLLUTANTS built-in cooling system if necessary. Such an approach may be necessary for electronic systems operating un- Specific design steps for protection against the effects der conditions that make it unfeasible to install air of pollutants are not common since protection Is nor- conditioning in a building.

This could include equip- mally obtained by methods employed for protection ment operating ia combat areas or any mobile or against other environmental factors. A preferred semimobile electronic equipment. Design changes of method, which Is receiving much attention, is to avoid this type also improve the equipment ability to operate such effects by reducing pollution levels or by avoiding in sand and dust, marine, and high humidity environ- regions with high pollution levels. On a local level, elec. ments. tronic facilities can be Isolated from areas In which large amounts of engine exhausts or combustion products are (3) Electronic deyices Semiconductor devices, inte- produced.

In speciflc instances, the information in the grated circuits, relays, switches, etc. have proved to be following subparagaphs may be useful: susceptible to air pollutants, starting with the fabric&- hibit varying degrees of susceptibility to atmospheric some highly industrialized areas with high concentra. pollutants. Therefore, the proper choice of metal or tions of air pollutants, it has been necessary to fabricate alloy is important for equipment components that will semiconductor devices and integrated circuits in "clean be exposed to polluted atmospheres. rooms".

Once fabricated they are encapsulated (her- (1) Metal components and structures Metals ex- tion stage and extending throughout their useful life. In 2-65