2007-10 SOI/DT-mdm FCPD-dp Quality-fz Alarm Possible fault E54 PCB faulty; current leakage from motor or from wiring. E61 NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. E62 NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. E66 PCB faulty. E68 Earth-leakage between heater and earth. E69 Washing heating element interrupted (thermofuse open) E71 Faulty NTC sensor; Wiring faulty; PCB faulty. E74 NTC sensor improperly positioned; Faulty NTC sensor; Wiring faulty; PCB faulty. E82 PCB faulty (Wrong configuration data). Selector, wiring E83 PCB faulty (Wrong configuration data). Selector, wiring E93 Incorrect configuration data; PCB faulty.
E94 Incorrect configuration data; PCB faulty. E97 Faulty PCB (Wrong configuration data). EA1 Wiring faulty; Circuit board faulty; DSP sensor faulty; Motor drive belt broken. EA6 Basket cover open. Motor faulty; Wiring faulty ; PCB faulty. EH1 Power supply problems (incorrect / disturbance); PCB faulty. EH2 Power supply problems (incorrect / disturbance); PCB faulty. EH3 Power supply problems (incorrect / disturbance); PCB faulty. EF1 Drain tube blocked/kinked/too high; Drain filter dirty/blocked. EF2 Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked. EF3 Water leaks onto base frame; water control system defective.
EF5 Load too unbalanced; f inal spin phases skipped. E00 ---------------- Alarm Possible fault Action/machine status Reset Page E54 PCB faulty; current leakage from motor or from wiring. Cycle blocked, door locked (after 5 attempts). RESET 41 E61 NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. The heating phase is skipped. START/RESET 42 E62 NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. Safety drain cycle – Cycle stopped with door open. RESET 43 E66 PCB faulty. Safety drain cycle – Cycle stopped with door open. RESET 44 E68 Earth-leakage between heater and earth. Cycle blocked with door open.
RESET 45 E69 Washing heating element interrupted (thermofuse open) ---------------- START/RESET 46 E71 Faulty NTC sensor; Wiring faulty; PCB faulty. Heating is skipped. START/RESET 47 E74 NTC sensor improperly positioned; Faulty NTC sensor; Wiring faulty; PCB faulty. Heating is skipped. START/RESET 48 E82 PCB faulty (Wrong configuration data). Selector, wiring ---------------- RESET 49 E83 PCB faulty (Wrong configuration data). Selector, wiring Cycle cancelled. START/RESET 50 E93 Incorrect configuration data; PCB faulty. Cycle interrupted. OFF/ON 51 E94 Incorrect configuration data; PCB faulty. Cycle interrupted. OFF/ON 51 E97 Faulty PCB (Wrong configuration data). Cycle interrupted.
RESET 51 EA1 Wiring faulty; Circuit board faulty; DSP sensor faulty; Motor drive belt broken. Drum positioning phase skipped. ON/OFF RESET 52 EA6 Basket cover open. Motor faulty; Wiring faulty; PCB faulty. Cycle interrupted. ON/OFF RESET 53 EH1 Power supply problems (incorrect / disturbance); PCB faulty. Wait for frequency nominal conditions. OFF/ON 54 EH2 Power supply problems (incorrect / disturbance); PCB faulty. Wait for voltage nominal conditions. OFF/ON 54 EH3 Power supply problems (incorrect / disturbance); PCB faulty. Wait for voltage nominal conditions. OFF/ON 54 EF1 Drain tube blocked/kinked/too high; Drain filter dirty/blocked. Warning displayed at the end of cycle (specific LED).
START/RESET 55 EF2 Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked. Warning displayed after 5 attempts or by the specific LED. RESET 55 EF3 Water leaks onto base frame; water control system defective. Machine drains and cycle stops RESET 55 EF5 Load too unbalanced; final spin phases skipped. ---------------- START/RESET 55 E00 ---------------- ---------------- ----------------