HP OmniBook XE2 Troubleshooting and Diagnostics 3-15 0603h For the external loop-back test, make sure the loop-back connector is installed and constructed properly. For the external or internal loop-back test, replace the motherboard. 0604h - 0605h Replace the motherboard. 0606h For the external loop-back test, make sure the loop-back connector is installed and constructed properly. For the external or internal loop-back test, replace the motherboard. 0607h Make sure the loop-back connector is installed and constructed properly. Replace the motherboard. 0608h - 0617h Replace the motherboard.
Parallel Port Tests 0701h For the external loop-back test, make sure the loop-back connector is installed and constructed properly. For the external or internal loop-back test, replace the motherboard. 0702h Replace the motherboard. 0703h Run BIOS Setup and disable ECP for the parallel port, then rerun the test. Replace the motherboard. 0704h - 0706h Replace the motherboard. 0707h Connect the loop-back connector. 0708h Replace the motherboard. Audio Tests 0801h - 0816h If this error also occurs for an external headphone, replace the motherboard (or VGA PCA for the OB 4150). Otherwise, check the speaker connections, replace the speakers.
If it occurs only for an external headphone, replace the audio jack PCA. 9003h - 9004h (See Microphone Tests near end of table.) Video Tests 0900h - 0901h Replace the VGA PCA. 0903h - 0906h Replace the LVDS PCA. Replace the VGA PCA. 0907h - 0908h Replace the VGA PCA. 0909h - 090Ah Replace the LVDS PCA. Replace the VGA PCA. 090Ch - 090Fh Replace the VGA PCA. 0920h Replace the LVDS PCA. Replace the VGA PCA. 8000h (See LCD Test near end of table.) CD-ROM Tests 0A00h Insert a CD in the drive. 0A01h Rerun the test. Replace the CD-ROM drive. 0A02h No repair. (Automatic close not supported.) 0A03h Insert a different CD in the drive. Check the connectors on the CD-ROM drive and motherboard.
Replace the CD-ROM drive. 0A04h Insert a computer CD in the drive. 0A05h Insert a different CD in the drive. Check the connectors on the CD-ROM drive and motherboard. Replace the CD-ROM drive. 0A06h Insert an audio CD in the drive. SMBus Tests 0E00h - 0E10h Replace the motherboard. ATAPI Removable Tests (LS-120) 0F02h - 0F03h Rerun the test. Insert a different disk in the LS- 120 drive. Check the connectors on the LS-120 drive and motherboard. Replace the LS-120 drive. 0F04h - 0F05h Replace the LS-120 drive. TI CardBus Tests 1201h Memory space not available. Remove any attached ISA or PCI cards. 1202h - 1203h Replace the motherboard. 1205h - 1206h Insert a different PC Card.
Replace the PCMCIA socket. Replace the motherboard. USB Tests 1301h Reprogram the BIOS IC. Replace the BIOS IC. Replace the motherboard. 1302h - 1312h Replace the motherboard. 9006h (See USB Port Test near end of table.) LCD Test 8000h If the test fails with an external monitor (must support VESA mode 105h), replace the VGA PCA, replace the motherboard. Otherwise: - If the shaded-band test fails, check the LCD flex cable connection in the bottom case, replace the LVDS PCA, replace the LCD flex cable, replace the VGA PCA, replace the motherboard. - If only a solid-color test fails, see chapter 5 for cosmetic guidelines, replace the LCD module.
Microphone/Line-In Tests 9003h If the error occurs for built-in and external microphones, replace the motherboard (or VGA PCA for the OB 4150). If it occurs for only the built-in microphone, check the LCD flex cable connection, replace the inverter PCA. If it occurs only for an external microphone, replace the audio jack PCA. 9004h Replace the audio jack PCA. Replace the motherboard (or VGA PCA for the OB 4150). Suspend/Resume Test 9005h Run BIOS Setup and restore default settings. Reprogram the BIOS IC. Replace the BIOS IC. Replace the motherboard. USB Port Test 9006h Make sure a USB device is connected to the port you are testing. Select the correct speed for the device.
Replace the motherboard (or dock component, if applicable).