Super Micro X6DVL-G/X6DVL-EG User Manual PDF: Руководство по установке и использованию (EN)

S UPER X6DVL-G X6DVL-EG USER’S MANUAL Revision 1.0c

Стр. 1

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. SUPER MICRO COMPUTER, INC. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice.

This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent. IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.

SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product. FCC Statement:

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate” WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Manual Revision: Rev. 1.0c Release Date: Oct. 9, 2007 Unless you request and receive written permission from SUPER MICRO COMPUTER INC., you may not copy any part of this document.

Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright © 2007 by SUPER MICRO COMPUTER INC. All rights reserved. Printed in the United States of America

Стр. 2

Preface Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the X6DVL-G/X6DVL-EG motherboard. The X6DVL-G/X6DVL-EG supports single or dual Intel Xeon EM64T (Nocona TM ) processors at a Front Side Bus of up to 800 MHz. Based upon Intel's NetBurst microarchitecture, the Nocona processor supports IA-32 and IA-64 software and includes features found in the Xeon TM processor such as Hyper Pipelined Technology, which includes a multi-stage pipeline, allowing the processor to operate at much higher core frequencies than the traditional processor.

Packaged in a 604-pin Flip Chip Micro Pin Grid Array(FC- mPGA4) platform in a Zero Insertion Force(ZIF) socket (mPGA 604), the Nocona Processor (800 MHz) supports Hyper-Threading Technology and is ideal for high performance workstation and server environments with up to two processors on one system bus. Please refer to the motherboard specifi cations pages on our web site (http: //www.supermicro.com/products/motherboard/) for updates on supported processors. This product is intended to be professionally installed.

Manual Organization Chapter 1 begins with a checklist of what should be included in your mainboard box, describes the features, specifi cations and performance of the motherboard and provides detailed information about the chipset. Chapter 2 begins with instructions on handling static-sensitive devices. Read this chapter when you want to install the processor and DIMM memory modules and when mounting the mainboard in the chassis. Also refer to this chapter to connect the fl oppy and hard disk drives, SCSI drives, the IDE interfaces, the parallel and serial ports, the keyboard and mouse, the power supply and various control panel buttons and indicators.

If you encounter any problems, see Chapter 3 , which describes troubleshooting pro- cedures for the video, the memory and the setup confi guration stored in CMOS. For quick reference, a general FAQ [Frequently Asked Questions] section is provided. Chapter 4 includes an introduction to BIOS and provides detailed information on running the CMOS Setup utility. Appendix A lists BIOS Error Beep Codes and DS LED POST Codes. Appendix B provides BIOS POST codes. Appendix C provides software installation instructions. iii

Стр. 3

X6DVL-G/X6DVL-EG User's Manual Table of Contents Preface About This Manual ...................................................................................................... iii Manual Organization ................................................................................................... iii Chapter 1: Introduction 1-1 Overview ......................................................................................................... 1-1 Checklist ................................................................................................... 1-1 Contacting Supermicro .............................................................................

1-2 X6DVL-G/X6DVL-EG Image .................................................... 1-3 X6DVL-G/X6DVL-EG Layout .................................................... 1-4 X6DVL-G/X6DVL-EG Quick Reference ................................... 1-5 Motherboard Features ................................................................................ 1-6 Intel E7320 (Lindenhurst VS) Chipset: System Block Diagram .............. 1-8 1-2 Chipset Overview ........................................................................................... 1-9 1-3 Special Features ...........................................................................................

1-10 BIOS Recovery ...................................................................................... 1-10 Recovery from AC Power Loss .............................................................. 1-10 1-4 PC Health Monitoring ........................................................................................... 1-10 1-5 ACPI Features .............................................................................................. 1-11 1-6 Power Supply ............................................................................................... 1-13 1-7 Super I/O ........................................................................................................ 1-13 Chapter 2:

Installation 2-1 Static-Sensitive Devices ................................................................................. 2-1 Precautions ................................................................................................ 2-1 Unpacking ................................................................................................ 2-1 2-2 Processor and Heatsink Installation ............................................................... 2-2 2-3 Installing DIMMs ............................................................................................. 2-5 2-4 I/O Ports/Control Panel Connectors ...............................................................

2-6 2-5 Connecting Cables ......................................................................................... 2-8 ATX Power Connector ............................................................................ 2-8 Processor Power Connector ................................................................... 2-8 NMI Button ............................................................................................... 2-9 Power LED ............................................................................................... 2-9 HDD LED ..............................................................................................

2-10 NIC1 LED .............................................................................................. 2-10 Overheat/Fan Fail LED ......................................................................... 2-11 iv

Стр. 4