A+ Server 2020A-8R User's Manual PDF Download (EN)

A+ S ERVER 2020A-8R NIC 1 NIC 2 USER’S MANUAL 1.0

Стр. 1

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site. The manufacturer reserves the right to make changes to the product described in this manual at any time and without notice.

This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent. IN NO EVENT WILL THE MANUFACTURER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. The manufacturer's total liability for all claims will not exceed the price paid for the hardware product. Unless you request and receive written permission from the manufacturer, you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2005 All rights reserved. Printed in the United States of America

Стр. 2

Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the A+ Server 2020A-8R. Instal- lation and maintainance should be performed by experienced technicians only. The 2020A-8R is a high-end 2U rackmount server based on the SC823S-R500LP server chassis and the H8DA8 serverboard, which supports single or dual AMD Opteron 200 series processors and up to 32 GB of ECC registered DDR266/200 or 16 GB of ECC registered DDR400/333 SDRAM memory. Manual Organization Chapter 1:

Introduction The fi rst chapter provides a checklist of the main components included with the server system and describes the main features of the H8DA8 serverboard and the SC823S-R500LP chassis, which make up the 2020A-8R. Chapter 2: Server Installation This chapter describes the steps necessary to install the 2020A-8R into a rack and check out the server confi guration prior to powering up the system. If your server was ordered without processor and memory components, this chapter will refer you to the appropriate sections of the manual for their installation. Chapter 3:

System Interface Refer here for details on the system interface, which includes the functions and information provided by the control panel on the chassis as well as other LEDs located throughout the system. iii

Стр. 3

A+ Server 2020A-8R User's Manual Chapter 4: System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the 2020A-8R. Chapter 5: Advanced Serverboard Setup Chapter 5 provides detailed information on the H8DA8 serverboard, including the locations and functions of connectors, headers and jumpers. Refer to this chapter when adding or removing processors or main memory and when reconfi guring the serverboard. Chapter 6: Advanced Chassis Setup Refer to Chapter 6 for detailed information on the SC823S-R500LP 2U rackmount server chassis.

You should follow the procedures given in this chapter when install- ing, removing or reconfi guring SCSI or peripheral drives and when replacing the system power supply unit and cooling fans. Chapter 7: BIOS The BIOS chapter includes an introduction to BIOS and provides detailed informa- tion on running the CMOS Setup Utility. Appendix A: BIOS POST Messages Appendix B: BIOS POST Codes Appendix C: System Specifi cations iv

Стр. 4