[Test program] Test programs on the MPC1000 can be run either using a Test OS or a JIG PC Flash Rom. [Running the test Program using a Test OS ] A test program can be installed on the MPC1000 by updating it with a Test OS. The Test OS must be copied to a CF card from which it will be written to the Flash ROM of the MPC1000. The installation procedure is the same as for a normal OS update. For a description of the test mode functions, refer to the “MPC1000 Test Program list”. Note: Once the Test OS is installed, the unit will always start up using the Test OS, until the regular OS is re-installed.
[Running the test Program using a JIG PC Flash ROM MPC1K (AJ - 771312J)] The PC Flash ROM is used during repair for the testing jig and boot block recovery. To access the test program on the PC Flash ROM MPC1K follow this procedure: 1. Turn off the MPC1000 and open the unit. 2. Insert the PC Flash MPC1K ROM into J110 on the CPU board. 3. Turn on the MPC1000 to start up the Test OS from the PC Flash ROM. MPC1000 TEST OS SERVICE MANUAL 8 By Pressing Keys correspond 35 boxes change to negative.(#1) JOG,FADER1,FADER2,input,value,displyed Each Pad No., and input value displayed. Plural input displayed "Error" All dot of LCD change to Black.
Contrast adjusting by JOG All LEDs light (#2)When press Keys with LED, LED light while pressing switches. (#1Press F6 twice = EXIT) SDRAM simple check SDRAM all area READ/WRITE check CF card simple check Type of CF card display CF card all area READ/WRITE check For development Delete CF card data HDD simple check Type of HDD displayed HDD all area READ/WRITE check For development Delete HDD dataHDD No function Write Test OS to Flash ROM Data (OS/Liblary) transport via USB No function No function A/D inputting signal output to all OUTPUT. SPDIF inputting signal output to all OUTPUT. (#3) FULL bit signal output to all OUTPUT.
(#3)A/D-L > MAIN-L, 1,3 A/D-R >MAIN-R, 2,4 Start Loop back Test, MIDI OUT A --> MIDI IN 1, MIDI OUT B --> MIDI IN 2 SIMPL ----- FULL- ----- ----- EXIT- SIMPL DETEC SECTR BACUP ERASE EXIT- SIMPL DETEC SECTR BACUP ERASE EXIT- P_OS- -USB- LIBC- LIBH- ----- EXIT- F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 "SDRAM TEST" "CF CARD TEST" "HDD TEST" "FLASH WRITING" -KEY- -JOG- -PAD- -LCD- -LED- EXIT- SDRAM -CF-- -HDD- -DSP- FLASH EXIT- -A/D- SPDIF TONE- ----- ----- EXIT- START ----- ----- ----- ----- EXIT- ----- ----- ----- ----- ----- EXIT- F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 "PANEL TEST" "MEMORY TEST" "A/D selected" "SPDIF selected" "test tone" "OUTA > IN 1:OK OUTB > IN2 FAILED (Each connection result dislayed) "F.SW1 :
ON F.SW2 : OFF" (Foot SW status displayed) PANEL MEMORY AUDIO MIDI- F.SW- ----- F1 F2 F3 F4 F5 F6 Starting Display