Supermicro SuperServer 6011L User's Manual PDF (P3TDLR / SC810 1U Server) (EN)

S UPER ® S UPER S ERVER 6011L USER’S MANUAL 1.0a

Стр. 1

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. SUPERMICRO COMPUTER reserves the right to make changes to the product described in this manual at any time and without notice.

This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent. IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product. Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2002 by SUPER MICRO COMPUTER INC. All rights reserved. Printed in the United States of America.

Стр. 2

Preface Preface About This Manual This manual is written for professional system integrators and PC techni- cians. It provides information for the installation and use of the Super- Server 6011L. Installation and maintainance should be performed by expe- rienced technicians only. The SuperServer 6011L is a high-end dual processor 1U rackmount server based on the SC810 1U rackmount server chassis and the P3TDLR, a dual processor motherboard that supports single or dual Intel Pentium ® III FCPGA 500 MHz-1.4+ GHz DP processors and single or dual low power Pentium ® III processors at front bus speeds of 133 and 100 MHz and up to 4 GB SDRAM main memory. CPU watchdog capability is also supported.

Manual Organization Chapter 1: Introduction The first chapter provides a checklist of the main components included with the server system and describes the main features of the SUPER P3TDLR mainboard and the SC810 chassis, which make up the SuperServer 6011L. Chapter 2: Server Installation This chapter describes the steps necessary to install the SuperServer 6011L into a rack and check out the server configuration prior to powering up the system. If your server was ordered without processor and memory components, this chapter will refer you to the appropriate sections of the manual for their installation. Chapter 3:

System Interface Refer here for details on the system interface, which includes the functions and information provided by the control panel on the chassis as well as other LEDs located throughout the system. iii

Стр. 3

S UPER S ERVER 6010L Manual Chapter 4: System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 6011L. Chapter 5: Advanced Motherboard Setup Chapter 5 provides detailed information on the P3TDLR motherboard, includ- ing the locations and functions of connections, headers, jumpers, DIP switches and IRQs. Refer to this chapter when adding or removing proces- sors or main memory and when reconfiguring the motherboard. Chapter 6: Advanced Chassis Setup Refer to Chapter 6 for detailed information on the SC810 1U rackmount server chassis.

You should follow the procedures given in this chapter when installing, removing or reconfiguring SCSI or peripheral drives and when replacing system power supply units and cooling fans. Chapter 7: BIOS The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility. Appendix A: BIOS Error Beep Codes and Messages Appendix B: Post Diagnostic Error Messages Appendix C: List of Figures Appendix D: System Specifications iv

Стр. 4