V410-H Handheld Reader Quick Start Guide (EN)

Add a Tab Key Return to Factory Defaults / Add an Enter Key Step 1 – Set Up Host Interface Return to Factory Defaults Add a Tab Key Decode the symbol below to return reader parameters to factory defaults. Decode the symbol below to add a Tab key after decoded data. USB Note: Cables may vary depending on configuration. USB Add an Enter Key USB Caps Lock Override Options Decode the symbol below to add an Enter key after decoded data. (Carriage Return / Line Feed) USB - OVERRIDE CAPS LOCK KEY (ENABLE) Decode one of the symbols below. The interface cable automatically detects the host interface type and uses the default setting.

If the default (*) does not meet your requirements, decode the other host symbol below. *USB - DO NOT OVERRIDE CAPS LOCK KEY (DISABLE) *USB HID KEYBOARD EMULATION SNAPI WITH IMAGING INTERFACE Step 1 – Set Up Host Interface (Cont.) Step 2 – Install WebLink PC and Connect Step 3 – Explore the Start View RS-232 Install The WebLink PC installer is found on Omron’s Download Center at www.automation.omron.com/weblinkpc Minimum PC Requirements The Start view shows all the readers available to the system. The Reader Model , Serial Number , and Firmware Version of each reader are displayed. This view also allows you to choose Assisted Setup , Create a New Setup , or Load a Setup .

The Gear icon in the upper right brings up the Settings Menu . • Intel ® Core™2 Duo Processor (Core™i3 recommended) • Microsoft Windows 7 32-bit (Windows 7 64-bit or Windows 10 recommended) • Internet Explorer 11 or higher, Edge, Firefox, or Opera (Chrome recommended) • 1 GB/128 MB Video RAM (2 GB RAM/128 MB Video RAM recommended) • 100 MB hard drive space (500 MB recommended) • 16-bit color display (32-bit recommended) • 3.0 Windows Experience Index (4.0 recommended) Connect To start WebLink PC , double-click the icon placed on your desktop during installation.

You can also start WebLink PC by opening a browser of your choice and typing http://localhost:8090 or http://127.0.0.1:8090 in the address bar. WebLink PC The WebLink PC session will begin after you enter the IP address. Decode the symbol to the right. Step 6 – Configure the Reader Step 4 – Create or Load a Setup Step 5 – Explore the Setup View Assisted Setup When you click the Assisted Setup button in the Start view, a dialog appears asking a series of application-related questions. Based on your answers, WebLink PC generates your initial setup automatically. Once the setup is created, you can fine-tune its parameters in the Setup view.

The Setup view allows you to configure the reader, view the current captured image, and view decoded symbol data. Cycle Step The Cycle step allows you to choose between Manual and Presentation trigger modes. In Manual mode, a decode is attempted when you pull the trigger. In Presentation mode, the read cycle begins when a symbol is detected moving into the reader’s field of view. The following read cycle steps are shown at the left side of the screen: • Cycle • Performance • Decode • Format Output Note: The reader is automatically set to Presentation mode when placed in the V410-H Stand. Create a New Setup The Start view also allows you to create a New Setup without using Assisted Setup .

When you click the Create a New Setup button, WebLink PC searches for any differences from default in the reader parameters. If no differences from default are found, the Setup view appears. If differences from default are found, an alert appears asking if you want to restore default settings. Load a Setup Select Load a Setup to load an existing .rls WebLink PC setup file. Step 7 – Run the Application Step 6 – Configure the Reader (Continued) Step 6 – Configure the Reader (Continued) Performance Step (DPM Optimization) The Performance step allows you to optimize the reader for Direct Part Mark ( DPM ) decoding.

A DPM is a permanent mark created by laser etch, chemical etch, or other method directly on a substrate. DPMs are often harder to read than other symbols, and may require a few attempts before finding optimal settings. The Decoder Effort slider has four settings: Level 1 , corresponding to Min on the slider; Level 2 ; Level 3 ; and Level 4 , corresponding to Max on the slider. As Decoder Effort is moved toward Max , the decoder spends an increasing amount of time trying to decode the symbol. Decode Step The Decode step allows you to select which symbologies to enable and disable. Clicking the 1D and 2D checkboxes will enable or disable all the symbologies in that group.

The Gear icon brings up a Symbology Settings dialog, allowing you to modify specific parameters. The Run view allows you to keep track of your application during runtime. The current captured image is shown along with a row of image control tools. A history of decoded symbol data is shown in the right pane along with any preambles or postambles that have been defined. In Level 4 , you can also enable the Enhance option, which improves readability by allowing additional processing for poorly-formed marks. Format Output Step Format Output allows you to configure preambles and postambles to add to symbol data output.

The Simplified version of this control allows you to Append Return or Append Tab after each string of data output. The Advanced version allows you to choose from a wide variety of keyboard characters that can be output as a preamble or postamble. You can also add a second postamble if required. The Illumination options are Direct , Indirect , and Cycle . Clicking the Question Mark icon brings up a dialog with more detail about each level of decoder effort. The Output Data display in the right pane shows a list of previous read cycle results. Each result is selectable and erasable. Image control tools are available at the upper right of the image view.

Resize Image to Fit Image Area Zoom In Zoom Out Save Full-Size Image V410-H Handheld Reader Reader Features Accessories POST IN WORK AREA V410-H Stand 1 2 3 Quick Start Guide 1 LED Indicator 2 Reader Window 3 Reader Trigger

Стр. 1

V410-H Aiming V410-H Handheld Reader Sample Symbols For best results, aim the dot at the center of the symbol.

Data Matrix OmronMicroscan1234567890 QR Code OmronMicroscan1234567890 Code 39 OMRON1234 Interleaved 2 of 5 1234567890 AVOID EXTREME WRIST ANGLES Handheld Decoding Power up Low/medium/high beep Barcode decoded Medium beep Reader is on and ready to decode, or no power to reader Off Barcode is successfully decoded Green Transmission error detected; data is ignored 4 long low beeps Transmission error Red Successful parameter setting High/low/high/low beep Hands-Free (Presentation) Decoding Correct programming sequence performed High/low beep No power to reader Off Incorrect programming sequence, or Cancel barcode decoded Reader is ready to decode Green Low/high beep Barcode is successfully decoded Off Momentarily Transmission error Red Reader not Working No power to reader Check system power Reader is disabled Ensure correct host interface cable is used Reader Decoding Barcode, but Data not Transmitting to Host Host interface not configured properly Decode appropriate host parameter barcodes Interface cable is loose Ensure all cable connections are secure Invalid rule Program the correct rules Warranty For current warranty information, see:

ia.omron.com/product/cautions/common/agreements-before-purchase/index.html Health and Safety Recommendations Ergonomic Recommendations Technical Support For technical support, see: ia.omron.com/support/ Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.

• Reduce or eliminate repetitive motion • Maintain a natural position • Reduce or eliminate excessive force • Keep objects that are used frequently within easy reach • Perform tasks at correct heights • Reduce or eliminate vibration • Reduce or eliminate direct pressure • Provide adjustable workstations • Provide adequate clearance • Provide a suitable working environment • Improve work procedures English: For EU Customers: All products at the end of their life must be returned to Omron Microscan for recycling. For information on how to return product, please go to: www.ia.omron.com. Bulgarish: За клиенти от ЕС:

След края на полезния им живот всички продукти трябва да се връщат на Omron Microscan за рециклиране. За информация относно връщането на продукти, моля отидете на адрес: www.ia.omron.com. Čeština: Pro zбkaznнky z EU: Všechny produkty je nutnй po skonи enн jejich životnosti vrбtit spoleиnosti Omron Microscan k recyklaci. Informace o zpщsobu vrбcenн produktu najdete na webovй strбnce: www.ia.omron.com. Dansk: Til kunder i EU: Alle produkter skal returneres til Omron Microscan til recirkulering, ner de er udtjent. Lжs oplysningerne om returnering af produkter ре: www.ia.omron.com. Deutsch: Fьr Kunden innerhalb der EU:

Alle Produkte mьssen am Ende ihrer Lebensdauer zum Recycling an Omron Microscan zurьckgesandt werden. Informationen zur Rь cksendung von Produkten finden Sie unter www.ia.omron.com. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Omron Microscan για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση www.ia.omron.com στο Διαδίκτυο. Eesti: EL klientidele: kxik tooted tuleb nende eluea lxppedes tagastada taaskasutamise eesmдrgil Omron Microscan'ile. Lisainformatsiooni saamiseks toote tagastamise kohta kьlastage palun aadressi: www.ia.omron.com. Espacol:

Para clientes en la Uniyn Europea: todos los productos deberбn entregarse a Omron Microscan al final desu ciclo de vida para que sean reciclados. Si desea mбs informa ciyn sobre cymo devolver un producto, visite: www.ia.omron.com. Franзais : Clients de l'Union Europйenne : Tous les produits en fin de cycle de vie doivent ktre retournйs а Omron Microscan pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : www.ia.omron.com. Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Omron Microscan al fine di consentirne il riciclaggio .

Per informazioni sulle modalita di restituzione, visitare il seguente sito Web: www.ia.omron.com. Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Omron Microscan otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nog ādāšanu Omron Microscan, lūdzu, skatiet: www.ia.omron.com. Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Omron Microscan“. Daugiau informacijos, kaip grąžinti gaminį, rasite: www.ia.omron.com. Magyar: Az EU-ban vбsбrlyknak: Minden tцnkrement termйket a Omron Microscan vбllalathoz kell eljuttatni ъjrahasznosнtбs cйljбbyl.

A termйk visszajuttatбsбnak mydjбval kapcsolatos tudnivalykйrt lбtogasson el a www.ia.omron.com weboldalra. Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Omron Microscan għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: www.ia.omron.com. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Omron Microscan te worden teruggezonden voor recycling. Raadpleeg www.ia.omron.com voor meer informatie over het terugzenden van producten. Polski: Klienci z obszaru Unii Europejskiej:

Produkty wycofane z eksploatacji naleїy zwryciж do firmy Omron Microscan w celu ich utylizacji. Informacje na temat zwrotu produkt yw znajduj№ sik na stronie internetowej www.ia.omron.com. Portuguks: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos а Omron Microscan para reciclagem. Para obter informaзxes sobre como devolver o produt o, visite: www.ia.omron.com. Romвnesc: Pentru clienţii din UE: Toate produsele, la sfвrşitul duratei lor de funcţionare, trebuie returnate la Omron Microscan pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi: www.ia.omron.com. Slovenčina: Pre zбkaznнkov z krajнn EU:

Všetky vэrobky musia b yť po uplynutн doby ich životnosti vrбtenй spoločnosti Omron Microscan na recyklбciu. Bližšie informбcie o vrбtenн vэrobkov nбjdete na: www.ia.omron.com. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Omron Microscan za reciklažo. Za informacije o vraиilu izdelka obišиite: www.ia.omron.com. Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrдtettдvдksi Omron Microscan-yhtiццn, kun tuotetta ei еnдд kдytetд. Lisдtietoja tuotte en palauttamisesta on osoitteessa www.ia.omron.com. Svenska: Fцr kunder inom EU:

Alla produkter som uppnett sin livslдngd meste returneras till Omron Microscan fцretervinning. Information om hur du returnerar produkten finns p е www.ia.omron.com. Tьrkзe: AB Мьşterileri iзin: Kullanım sьresi dolan tьm ьrьnler geri dцnьştьrme iзin Omron Microscan'ya iade edilmelidir. Ьrьnlerin nasıl iade edileceği hakkında bilgi iзin lьtfen şu adresi ziyaret edin: www.ia.omron.com. Waste Electrical and Electronic Equipment (WEEE) Regulatory Information Omron hereby declares that this device is in compliance with all applicable Directives, 2014/30/EU, 2014/35/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address:

Стр. 2