Volume 2 of 2 - CAB CID / MID / FMI ¹The FMI is a diagnostic code that indicates what type of failure has occurred. Component Identifiers (CID¹) Module Identifier (MID²) Machine Control System (MID No.
039) CID Component 0041 8 Volt DC Sensor Power Supply 0070 Parking Brake Switch 0168 Electrical System Voltage 0190 Engine Speed Sensor 0246 Proprietary CAN Data Link (CAN B) 0247 SAE J1939 Data Link (CAN A) 0262 5 Volt Sensor DC Power Supply 0473 Charge Pressure Sensor 0596 Implement Control 0681 Parking Brake Solenoid 0726 Right Hand Steering Solenoid 0727 Left Hand Steering Solenoid 0871 Slope Sensor 1326 ECM Location Code 1469 Steering Motor Speed Sensor #1 1470 Steering Motor Speed Sensor #2 1471 Steering Control Position Sensor #1 1472 Steering Control Position Sensor #2 1473 Steering Control Position Sensor #3 1482 10 Volt Sensor DC Power Supply 2305 Brake/Decelerator Pedal Position Sensor (Travel Control Pedal) 2500 Power Train Speed Range Control Position Sensor 2595 Service Brake Solenoid 2596 Brake Pressure Modulation Solenoid 2705 Cab Throttle Switch 2868 Power Train Oil Tank Temperature Sensor 2989 Reverse Desired Ground Speed Selection Switch (Travel Speed) 2993 Direction Selector (FNR) Position Sensor 1 2994 Direction Selector (FNR) Position Sensor 2 3083 Power Train Lube Pressure Sensor 3243 Water Pump Control Module 3428 Generator Control Module 3429 Motor Control Module 3527 Direction Selector Position 3642 Operator Speed Set/Recall Switch 3657 Operator In Seat Sensor Implement Control Module (MID No.
082) 0096 Fuel Level Sensor 0168 Electrical System Voltage 0171 Ambient Air Temperature Sensor 0247 J1939 Data Link 0262 5V Sensor DC Power Supply 0490 Implement Lockout Switch 0497 Tilt Right Solenoid 0498 Tilt Left Solenoid 0590 Engine Control Module 0600 Hydraulic Oil Temperature Sensor 0879 Ripper Shank In/Out Lever Sensor 0880 Ripper Raise/Lower Lever Sensor 0881 Ripper Auto Stow Switch 0882 Implement Lockout Solenoid 0886 Ripper Shank In Solenoid 0887 Ripper Shank Out Solenoid 0888 Ripper Shank Lower Solenoid 0889 Ripper Shank Raise Solenoid 1079 Blade Control Handle Lift Position Sensor 1197 Blade Control Handle Tilt Position Sensor 1197 Blade Lower Solenoid 1198 Blade Raise Solenoid 1298 All Implement Solenoids 1450 Main Hydraulic Pump Oil Pressure Sensor 1482 10 Volt Sensor DC Power Supply 1603 Machine Control Module 1870 Blade Thumb Rocker Position Sensor 1874 Winch Lockout Switch 1881 Winch Control Handle Spool In/Out Position Sensor 1882 Winch Control Handle Drum Release Position Sensor 1883 Winch Low Speed Lock Switch 1884 Winch Spool In Solenoid 1885 Winch Spool Out Solenoid 1886 Winch Drum Release Solenoid 1887 Winch Low Speed Lock Solenoid 2204 Auxiliary Lever 1 Position Sensor Event Codes Implement Control Event Code Condition E0281 Steering Hydraulic Oil Filter Restricted E0467 Blade Lift Control Out of Neutral at an Improper Time E0468 Blade Tilt Control Out of Neutral at an Improper Time E0469 Blade Pitch Control Out of Neutral at an Improper Time E0472 Ripper Shank In/Out Lever Out of Neutral at an Improper Time E0473 Ripper Lift Control Out of Neutral at an Improper Time E0474 Ripper Autostow Switch Pressed at an Improper Time E0475 Winch Spool In/Out Control Out Of Neutral At Improper Time E0476 Winch Drum Release Control Out Of Neutral At Improper Time E0655 High DC PowerBus E0673 Low DC PowerBus E0711 High Accessory Power Converter Temperature E0712 High Accessory Power Output Voltage E0713 Low Accessory Power Output Voltage E0714 High Battery Charger Current E0715 Ground Fault E0788 Auxiliary Lever 1 Out of Neutral at an Improper Time E0789 Auxiliary Lever 2 Out of Neutral at an Improper Time E0790 Auxiliary Lever 3 Out of Neutral at an Improper Time E0861 Clock Manual Alignment Required E0875 Low System Voltage E0876 High System Voltage E0878 Hydraulic Oil Temperature High E0887 Blade Function Disabled Due to System Fault E0888 Ripper Function Disabled Due to System Fault E0889 Winch Function Disabled Due to System Fault E0929 Battery Charger System not Charging E0987 High Battery Charger Temperature E0988 DC Ground Fault E0989 Drive Motor System AC Ground Fault E0990 High Accessory Bus Current E0999 Generator System AC Ground Fault E1066 Water Pump System AC Ground Fault E1071 Accessory Power Converter Cannot be Enabled E1078 Air Conditioner System AC Ground Fault E1136 Accessory Power Converter Ground Fault Detection Disabled E2075 Winch Low Speed Lock Switch Depressed At Inappropriate Time E2115 Implement Disabled Due to System Fault Event Codes Machine Control Event Code Condition E0192 Steering System Malfunction E0256 Steering in the Wrong Direction E0257 Steering Output Detected With No Command E0258 No Steering Detected With Command Given E0283 Charge Pressure Low E0658 High Power Converter (Inverter) 1 Temperature E0659 High Power Converter (Inverter) 2 Temperature E0692 Power Train Oil Tank Temperature High E0719 High Drive Motor Winding Temperature E0722 Power train Lube Pressure Low E0756 Generator Voltage Low E1064 Low Water Pump Speed E1968 Power Train Lube Pressure Sensor Open E2140 Power train Limited Due to System Fault Failure Mode Identifiers (FMI)¹ FMI No.
Failure Description 0 Data valid but above normal operational range. 1 Data valid but below normal operational range. 2 Data erratic, intermittent, or incorrect. 3 Voltage above normal or shorted high. 4 Voltage below normal or shorted low. 5 Current below normal or open circuit. 6 Current above normal or grounded circuit. 7 Mechanical system not responding properly. 8 Abnormal frequency, pulse width, or period. 9 Abnormal update. 10 Abnormal rate of change. 11 Failure mode not identifiable. 12 Bad device or component. 13 Out of calibration. 14 Parameter failures. 15 Parameter failures. 16 Parameter not available. 17 Module not responding. 18 Sensor supply fault. 19 Condition not met.
20 Parameter failures.