Altivar 16 AC Drive Filters, inductors Radio frequency interference (RFI) filters The use of RFI filters prevents radio frequency emissions from interfering with nearby antennas or conductors such as radios or televisions. For Drives Characteristics [1] Catalog Weigh Numbers lb (kg) ATV16U09M2, 16U18M2 208/240 V: 8 and 4 A VW3A16401 6.17 (2.80) ATV16U29M2 (single-phase input) 208/240 V: 14 and 7.1 A VW3A16402 7.72 (3.50) ATV16U29M2 (three-phase input) 400/460 V: 11.7 and 7.8 A VW3A16403 11.24 (5.10) ATV16U41N4, 16U54N4 ATV16U41M2 (single-phase input) 208/240 V: 20 and 10 A VW3A16404 8.82 (4.00) VW3A16406 ATV16U41M2 (three-phase input) 208/240 V:
15 and 10 A VW3A16405 13.01(5.90) ATV16U18N4, 16U29N4 400/460 V: 6.2 and 4.1 A VW3A16406 10.14 (4.60) ATV16U72N4 400/460 V: 15.8 and 10.5 A VW3A16407 13.01 (5.90) [1] Voltage and current for input and output filters. Description : RFI filter kits are IP20. The package consists of: - One filter module for the input of the drive allowing the Altivar to conform to VDE 871, CISPR11 and EN 50011 regarding the limitation of radio frequency interference in conduction mode. - One filter module for the output of the drive to limit interference from motor cables, ground leakage currents, and overvoltages at the motor connections if the cables are very long.
Inductors Inductors protect against input line overvoltage and reduce the current absorbed by the drive. When used between the drive and the motor, inductors limit ground leakage interference currents. For Drives Characteristics Catalog Weigh Numbers lbs (kg) ATV16U09M2, 16U18M2 5 mH - 6 A single-phase VW3A16501 4.41 (2.00) ATV16U29M2, 16U41M2 (single-phase) 2 mH - 16 A single-phase VW3A16502 6.39 (2.90) ATV16U29M2, 16U41M2 (three-phase) 1.7 mH - 11 A three-phase VW3A16503 9.92 (4.50) ATV16U54N4, 16U72N4 ATV16U18N4, 16U29N4, 16U41N4 5 mH - 6 A three-phase VW3A16504 6.83 (3.10) Description : Inductor kits are IP20. G Recommendations for use of line inductors:
G Recommendations for use of inductors between drive & motor: - Input lines subject to interference from other loads - Wire connecting drive and motor is very long - Drive controller supplied by a line with very low impedance - 3 or more motors are controlled in parallel - Large number of drive controllers installed on the same line - Motor has more than 6 poles and a high power factor with low stator inductance Mounting kit for Altivar 16 with filters Recommendations for use :
Description For Drives Catalog Weigh Numbers lbs (kg) ATV16U18N4 + VW3A16406 + VW3A16409 2 mounting rails AM1ED041 ATV16U09M2, 16U18M2 VW3A16408 1.87 (0.85) with AF1CG5 nuts 2 mounting rails AM1ED051 ATV16U29M2 to 16U72N4 VW3A16409 2.21 (1.00) with AF1CG5 nuts 9