Chapter 2 Devices 2_ 2-19 AS300 Series AS200 Series Latched Attribute Default OFF STOP RUN SM Function ON RUN STOP SM465 Alarm: positive limit for axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF SM466 Enabling the negative maximum value for axis 1 (Y0.0/Y0.1) ○ ○ – – – Y R/W OFF SM467 Alarm: negative limit for axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF *SM468 Enabling the S curve ramp-up/down for axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF SM469 Enabling fixed slope ramp-up/down for axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF SM470 Auto-reset for Y0.0/axis 1 (Y0.0/Y0.1) output is complete.
○ ○ OFF OFF – N R/W OFF SM471 Executing an interrupt I500 when pulse output ends for axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF SM472 Outputting Y0.1. ○ ○ OFF OFF – N R OFF SM473 Y0.1 output is complete. ○ ○ OFF OFF – N R/W OFF *SM474 Stopping the output of Y0.1. ○ ○ OFF OFF – N R/W OFF SM475 Auto-reset for Y0.1 output is complete.
○ ○ OFF OFF – N R/W OFF *SM476 Output immediately stops when the instruction is disabled or stops for Y0.0/axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF *SM477 Output immediately stops when the instruction is disabled or stops for Y0.1 ○ ○ OFF OFF – N R/W OFF SM478 Change the target positon while outputting Y0.0/axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF SM479 Change the target positon while outputting Y0.1 ○ ○ OFF OFF – N R/W OFF SM480 Outputting Y0.2/axis 2 (Y0.2/Y0.3). ○ ○ OFF OFF – N R OFF SM481 Y0.2/axis 2 (Y0.2/Y0.3) output is complete.
○ ○ OFF OFF – N R/W OFF SM482 Reversing the output direction of axis 2 (Y0.3) ○ ○ OFF OFF – N R/W OFF *SM483 Stopping the output of Y0.2/axis 2 (Y0.2/Y0.3) ○ ○ OFF OFF – N R/W OFF SM484 Enabling the positive maximum value for axis 2 (Y0.2/Y0.3). ○ ○ – – – Y R/W OFF SM485 Alarm: positive limit for axis 2 (Y0.2/Y0.3). ○ ○ OFF OFF – N R/W OFF SM486 Enabling the negative maximum value for axis 2 (Y0.2/Y0.3) . ○ ○ – – – Y R/W OFF SM487 Alarm: negative limit for axis 2 (Y0.2/Y0.3). ○ ○ OFF OFF – N R/W OFF *SM488 Enabling the S curve ramp-up/down for axis 2 (Y0.2/Y0.3). ○ ○ OFF OFF – N R/W OFF SM489 Enabling fixed slope ramp-up/down for axis 2 (Y0.2/Y0.3).
○ ○ OFF OFF – N R/W OFF SM490 Auto-reset for Y0.2/axis 2 (Y0.2/Y0.3) output is complete. ○ ○ OFF OFF – N R/W OFF SM491 Executing an interrupt I501 when pulse output ends for axis 2 (Y0.2/Y0.3). ○ ○ OFF OFF – N R/W OFF SM492 Outputting Y0.3. ○ ○ OFF OFF – N R OFF SM493 Y0.3 output is complete. ○ ○ OFF OFF – N R/W OFF *SM494 Stopping the output of Y0.3. ○ ○ OFF OFF – N R/W OFF SM495 Auto-reset for Y0.3 output is complete. ○ ○ OFF OFF – N R/W OFF *SM496 The output immediately stops when the instruction is ○ ○ OFF OFF – N R/W OFF