2-10 8. SPECIAL TOOLS • Special tools applicable to the parts except gear case Tool name Tool number Application 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Ring gear holder SCS service check connector Test harness Float level gauge Oil pressure gauge attachment Fuel pressure gauge set Oil pressure gauge set Valve guide driver, 5.5 mm Pin driver, 6.0 mm Attachment, 32 x 35 mm Attachment, 37 x 40 mm Attachment, 52 x 55 mm Attachment, 24 x 26 mm Driver, 22 mm I.D. Attachment, 15 mm I.D. Driver, 40 mm I.D.
Pilot, 12 mm Pilot, 15 mm Pilot, 20 mm Pilot, 30 mm Pilot, 22 mm Driver Valve spring compressor Valve spring compressor attachment Valve seat cutter, 45° 35 mm Valve seat cutter, 45° 33 mm Valve seat cutter, 32° 38.5 mm Valve seat cutter, 32° 33 mm Valve seat cutter, 60° 30 mm Valve seat cutter, 60° 37.5 mm Cutter holder, 5.5 mm Sensor socket wrench, 22 x 150L Attachment, 28 x 30 mm Oil seal driver attachment, 72 mm Oil seal driver Oil filter wrench Valve guide reamer, 5.525 mm Socket wrench, 19 mm Handle Pulley holder attachment, HEX 50 mm Belt tension gauge Air supply Stem seal driver 070PB-ZY60100 070PZ-ZY30100 070PZ-ZY60100 07401-0010000 07406-0030000 07406-0040003 07506-3000001 07742-0010100 07744-0010500 07746-0010100 07746-0010200 07746-0010400 07746-0010700 07746-0020100 07746-0020200 07746-0030100 07746-0040100 07746-0040300 07746-0040500 07746-0040700 07746-0041000 07749-0010000 07757-0010000 07757-PJ10100 07780-0010400 07780-0010800 07780-0012400 07780-0012900 07780-0014000 07780-0014100 07781-0010101 07906-PD10000 07946-1870100 07947-6340201 07947-SB00100 07HAA-PJ70101 07HAH-PJ70100 07JAA-001020A 07JAB-001020B 07JAB-0010400 07JGG-0010101 07LAJ-PR30102 07PAD-0010000 Flywheel boss, flywheel removal/installation ECU troubleshooting, idling adjustment ECU troubleshooting Vapor separator float level inspection Oil pressure test Fuel pressure inspection Oil pressure test Valve guide removal/installation Balancer shaft hold 22 x 35 x 7 mm water seal installation, Lower mount center hosing removal Alternator front bearing installation Alternator rear bearing, Chain case oil seal installation Alternator front bearing removal, 14 x 26 x 8 mm water seal installation Alternator rear bearing installation Alternator rear bearing installation Lower mount center housing installation 14 x 26 x 8 mm water seal installation Alternator front bearing removal/installation Mounting case needle bearing installation Lower mount center housing removal 22 x 35 x 7 mm water seal installation Driver for 10 through 13, 17 through 21, 33 through 35 and 48 Valve keeper removal/installation Valve seat reconditioning (IN) Valve seat reconditioning (EX) Valve seat reconditioning (IN) Valve seat reconditioning (EX) Valve seat reconditioning (EX) Valve seat reconditioning (IN) Valve seat reconditioning (IN/EX) A/F sensor removal/installation Mounting case needle bearing installation Oil pump body oil seal installation Oil pump cover oil seal installation Oil filter removal/installation Valve guide reaming Crankshaft pulley bolt removal/installation Alternator belt tension inspection VTEC system, VTEC valve inspection Valve stem seal A/B installation