US Army Materiel Command AMCP 706-250 — AMCP 706-250 Guns—General Engineering Design Handbook (1964) PDF (EN)

Downloaded from https://www.everyspec.com force a ramrod rearward against a spring, which, on release of a sear that engages the extended ram- ^ rod, drives the ramrod forward to propel the pro- ^ jectile into the cannon bore. Hydraulic power is provided by an electric motor, hydraulic pump and reservoir tank. The cylinder and ramrod are mounted above the gun breech; the ramrod moves parallel to and above the axis of the bore, carrying on its rear end a rammer head. This head consists principally of a folding arrangement of links, yoke and arm that extended downward terminates in a pad aligned with the gun axis, in position to drive the projectile forward into the bore.

Folded, the head clears the space back of the gun breech. In operation, a hand-carried tray is positioned in the breech recess and the projectile placed upon it. One switch is thrown to start the motor-driven pump and a second to open a solenoid-operated valve and admit pressure to the cylinder. The pressure moves the piston, ramrod and folded head rearward to sear engagement. A lever on the head is then operated manually, to unlatch the folded member and extend the projectile-driving arm downward to latched-open position. The sear is then disengaged by hand lever to permit the spring to drive the ramrod and head forward.

As the head completes ite forward travel, the latch holding the head extended is automatically tripped and the head folds into retracted position. The pro- pelling charge is then inserted by hand. 3-8.1.2.3.1 Fuze Setter The fuze setter housing is mounted above the gun, near the breech, on ways that permit it to slide rearward to encircle the nose of the projectile (held on the rammer tray) for rotation of the time- setting ring on the projectile, then slide forward to free the projectile for alignment with and in- sertion in the bore by the rammer unit.

The rear- ward and forward movement of the fuze setter is effected by a cam mounted ahead of the fuze setter and operating through an adjustable connecting rod. The cam is rotated by the driving motor, through a speed reducer and clutch, the latter having a combined automatic and manual engaging and disengaging mechanism. On manual engage- ment of the clutch, the cam is rotated through a half revolution to push the fuze setter rearward, then is automatically disengaged until the projec- tile fuze has been set.

Full entry of the projectile nose into the recess of the fuze setter closes a cir- cuit to energize the fuze setter and so rotate the fuze setter ring in accordance with data received from the director. On completion of the fuze set- ting, a solenoid automatically operates to effect re-engagement of the cam clutch to rotate the cam a half revolution, then disengagement of the clutch. The cam action withdraws the fuze setter to for- ward (rest) position, and the clutch disengagement completes the cycle. A brake interlinked with the clutch prevents over-rotation of the cam and holds the fuze setter firmly at each extremity of travel.

3-8.1.2.3 Power Rammer and Fuze Setter—- Separate Units 3-8.1.2.3.2 Rammer The essential components for receiving, aligning and ramming the ammunition are a tray supported on trunnions parallel to the gun bore and a sur- mounted, pivoted rammer arm that sweeps the tray surface. The tray, in its idle position, is approxi- mately level laterally and is situated rearward, above, and to the left of the breech ring of the gun. Its inner edge is bounded by a trough-shaped rim projecting upward, into which the ammunition is laid manually with the projectile placed foremost, against suitable locating stops, where it is held by a spring-loaded hold-down lever.

The projectile in this position is behind and in alignment with the fuze setter and is so held until the fuze setter has completed its operation. On its forward with- drawal the fuze setter actuates engagement of the rammer clutch to connect the driving motor, An arrangement of this type (Figure S-20) has been used for inserting the two units of a round of separated ammunition, i.e., a time-fuzed projec- tile and a cartridge case containing primer and propellant.

The rammer and mechanical fuze setter are individual units, each having a speed reducer, clutch and appropriate controls, but driven by a single electric motor, and with control mechanisms interconnected to enable the two units to be oper- ated separately or in combination. A gun of the vertically sliding breechblock type, with rammer and fuze setter units as indicated below, requires manual operations to place the ammunition com- ponents on the tray, to engage the fuze setter clutch, and to fire the weapon. 3—19