US Army Materiel Command AMCP 706-250 — AMCP 706-250 Guns—General Engineering Design Handbook (1964) PDF (EN)

Downloaded from https://www.everyspec.com 5-3 Granulation 5-3.1 Purpose for progressive than for degressive propellants (see Figure 5-1). If charges of the two types of granu- lations are to impart the same muzzle velocity -to the projectile, the areas under the respective pres- sure-travel curves must be equal. If the lengths of travel are also equal, the pressure curve of the progressive propellant, having a more gradual de- cline, will have a lower maximum. However, the slower reduction of pressure (and temperature) exhibited by progressive propellants results in slightly higher gas pressure (and temperature) at exit from the muzzle.

This signifies a lower effi- ciency, i.e., a smaller portion of the energy gen- erated by the propellant is transmitted to the projectile. Hence, for the same muzzle velocity, the quantity of propellant required is somewhat larger for progressive than for degressive propel- lants. An alternative to increasing the quantity of propellant is to increase the length of the bore, and so utilize a greater length of the declining pressure curve. In general, the effect of shifting from degressive to progressive granulation is to reduce structural strength requirements in the chamber region and increase strength requirements near the muzzle.

The resulting alteration of the gun tem- perature curve corresponds to that of the pressure curve. The purpose of establishing a definite size and shape of granulation is to so control the rate of combustion (gas evolvement) that the requisite energy will be applied to the projectile without exceeding permissible pressure (and temperature) at any stage of the projectile's travel through the barrel. 5-3.2 Effect of Grain Form Grain form is used to influence the quantity rate at which the propellant burns.

Since combustion takes place only at the grain surface, the amount of propellant burned per unit of time, at a given linear rate, is directly proportional to the surface area of the burning grains. The surface area of grains of solid section (rods or strips) decreases as burning progresses, thus exerting a decelerating influence on the quantity rate of combustion. Propellants of such grain form are termed degressive. To effect other than degressive burning, perfo- rated grains are employed. Cylindrical tubular grains have one axial perforation (typical form for U. S.

small arms) maintain nearly the same area of surface until practically consumed, since the inner periphery increases as the outer periphery decreases. A propellant that maintains a uniform quantity rate of burning" is termed neutral. 5-3.3 Effect of Web Thickness An increasing rate of burning may be effected by using multiple longitudinal perforations through a grain with cylindrical or fluted exterior. (Typi- cal U. S.

cannon propellants have a cylindrical grain with seven perforations, one axial and six equally spaced about the center, at mid-wall.) With more than one perforation the interior sur- face increases more rapidly than the outer surface reduces, so that the quantity rate of combustion increases as burning progresses. A propellant with grains formed so as to effect an accelerating burn- ing rate is termed progressive. The web thickness is a most important factor in the control of propellant combustion to obtain a desired shape of pressure-travel curve. Web thick- ness is defined as the least thickness of propellant material between opposite surfaces on which burn- ing occurs.

The geometric shape of the grain affects comparative rates of burning from ignition to completion (all burnt), while the web thickness affects the total time required to completely con- sume the grain and, hence, the time required to completely burn the propellant charge. A web too thin will permit completion of combustion before the projectile can be moved a sufficient distance forward in the bore, with resulting excessive pres- sure and temperature.

A web too thick will delay the development of the peak of pressure until the projectile is too far forward, so that the maximum pressure is undesirably low, subsequent expansion is therefore less complete before exit, and gas pres- sure and temperature remain undesirably high at discharge from the muzzle. If a degressive grain is used, the maximum rate of combustion will be reached quickly after com- pletion of ignition, and a decreasing rate will fol- low. With a progressive grain, the maximum rate of combustion occurs somewhat later, when the projectile is farther forward and advancing more rapidly.

Graphically, the effect is that the declin- ing portion of the pressure-travel curve is less steep