US Army Materiel Command AMCP 706-250 — AMCP 706-250 Guns—General Engineering Design Handbook (1964) PDF (EN)

Downloaded from https://www.everyspec.com and as far rearward as is feasible. However, weight not otherwise needed should not be incorporated for the purposes of increasing inertia or shifting the center of gravity, unless coordination with carriage design indicates such addition to be ad- vantageous. to withstand all stresses generated by firing ammu- nition that develops the design pressures, but provision of sufficient factor of safety to cover ^ unavoidable variations. These include:

variations flj in ammunition, from manufacturing tolerances or from changes in properties occurring in periods of storage; unavoidable variations in tube proper- ties, arising in manufacture; and deterioration of the tube from combined effects of heat, erosion, chemical effects, and progressive failure starting at minor cracks, inclusions, or other types of stress raisers. 6-2.6 Safety Safety in guns is of two-fold importance. Ob- viously, guns properly designed for safety in opera- tion are more dependable in performance, so that a smaller number are necessary to insure accom- plishment of a given mission.

But in addition, the safely-operable weapon not only reduces the like- lihood of injury to its operators, but engenders confidence and morale favorable to efficient opera- tion. Specific points to be considered follow: Avoidance of rupture of a tube in service is of major importance, since such a failure involves serious danger to the operators and to nearby equipment; and it completely disables the weapon in a manner not correctable in the field, unless the weapon has been specifically designed for field tube replacement. (1) Provision of a method of loading that per- mits rapid operation with minimum physical effort and minimum possibility of injury in the pro- cedure.

(4) Minor mechanical failures. A high degree of reliability of operation of all mechanical parts is of prime importance in guns intended for use against enemy personnel. Failure of a minor com- ponent can make the weapon inoperative in cir- cumstances where neither time nor replacement parts are available to remedy the deficiency, and the defection can jeopardize not only the operating individual or group, but others involved in the same action. (2) Adequate locking or interlocking devices to prevent unintentional firing of the weapon, or to prevent any violation of proper sequence of the operating cycle in such manner as to cause damage to the equipment or endanger personnel.

These devices may be mechanical or electrical, as best suited to the means of weapon operation. Examples include: "safety" levers or slides that block operation of firing mechanisms unless moved to firing position; mechanical interlocks that prevent mechanical ramming unless the breech is fully open, or that prevent the firing mechanism from functioning unless the breech is closed and locked; and electrical firing circuits that remain open and inoperative until closed by completion of breech locking.

Thorough control of the firing mechanism is particularly important, to prevent possibility of igniting the propellant before it is adequately confined in the chamber, or while being removed after a misfire, or on termination of firing. Automatic breech opening devices should also re- main inoperative while an unfired propellant charge remains in the chamber, so that, should a hangfire occur, the delayed explosion may be nor- mally confined rather than be free to blast through the opened breech. 6-2.7 Obturation With few exceptions, satisfactory performance and service life of guns are dependent on effective sealing of the breech against rearward escape of propellant gases.

In guns using cartridge cases, a seal is effected by pressure-expansion of the case ag. -ist the closely-fitting containing chamber surface, while the bolt or breechblock of the gun blocks the closed rear end of the case against rearward ejection. Contour, finish, and clearance of the chamber must be such that the case, when propellant pressure decays, can be withdrawn rearward without exces- sive effort. In guns not employing a cartridge case, another form of seal must be provided between the closing member (breechblock) and the tube.

The sealing member must be capable of rapid sealing and un- sealing as pressure is applied and released; retain its elastic properties under high rates of loading (3) Adequate tube strength to prevent failures from pressures generated by propellants. This requires not only adequate design for a new gun