— AMCP 706-286 — Engineering Design Handbook (1963) (EN)

Downloaded from https://www.everyspec.com 0l J STIZ4CW1RF Taking the shear force in the plane of Ube sisted by hoop or membrane stresses. Curved () cross-section passing through the center of two-dimensional elements are rturally effi- the circle, this force is tranbrii tted by means eient in this resect. A flat two-dimensional -f shear stresses which are symmetrically eleimen, or plate, can resist normal pressures dispose about the line of action of the re- only by means of its bending resistance. This sultant force. The variation is sinusoidal; generally gives rise to fairly high stresses.

varying from zero at the point of intersection On the 9ther hand, curved two-dimensional of the line of action of Vhe force and the cy.l- elements are able to supply tension force com- ind,-", to h maximum value at 90 degrees, and ponents opposite to the direction of the prea- back , zezo at lMl0 degrees. The maximum sure vector and therefore ar.- used wherever shear stress is twice the ntverage value ob- pos ble to withstand high normal pressures. La:-ed by dividing the-force by the cross-see- tior;al area. The axial force gives rise to a 4.5.

STRUCTURAL FAILURE uniform nom-al stress distribution whoae In analyzing 'he integrity of a design, thb value is given by the axial force divided by stress analyst considers yield and ultimate the cross-sectional azea. Turning now to t~e noments which are to rtrength, stiffness, fatigue strength, and be transmitted, it c~n be sown that the thin- buckling Assume that the designer has ten- be ranmitedit an e zowntha th thn- tatively chosen a structu-a! configration and walled circular cylinder is about one and one- tatel o atrcua conution half as efficient as a solid rectangular section the material or materla of construction.

Comparing these cxoss-sections on the basis Also assume that teitative cross-sectional of equal areas and equal maximum normal areas have been established. The primary stresses, the criterion is simply the sectu object then is to study the manner in which .. wdu!,us, which is the raio of the moment of the design criteria affect the cross-sectional inertia to the d;stance from the neutral axis arEi Ata very es'Jj stage in the design a tentative structm-e must )e lai out, or it to the extreme fibers.

The relative efficiencies would o be possible to cYculate preliminary of the I-beam, circular cylinder and solid raec- tangc!i- section are 1, '/,w and i respec- aerodynamic loads, thermal inputs, thermal tively. The thin-walled circular cylinder has 'tresses, ix.e {ia loads and other quantities. a moment oZ iaertia which is constant about 4-5.1o Yield and Ultimate Strength. The any diameter. Thus this shape can abs9rb a criteria established in analyzing the yield bending nomegit acting in any direction with and ultimate strength of a structure are es- equal facility. sentisly the following.

At limit load, the The remaining moment component, the structure should not suffer more than a c-er- torque, is most efficiently transmitted by the tain, maximum permanent deformation. A thin-w led circular section. In a circular 0.2% permanent set is ustally specified. The section the twisting rigidity (torque per unit integrity of the structure should be main- angle of twist) is proportional to its polar taied, i.e., no collapse or failure up to the momert of inertia. A tubular cross-section ultimate load. This means that the stress has a higher polar moment than a solid cir- analyst, in checking the yield strength of the cular section of the same area.

The torque structure, must perform stress calculations is resisted by a uniform distributon of shear for the limit loads under a variety of environ- stresses, and the moments by a distribution mental conditions and ascertain that the of normal stresses given by the well-known stresses nowhere exceed the yield stress of MC/I formula. the material of construction. In order to sim- It is to be noted that considerations of plify the calculations, the analyst generally bukling, concenttated loads, edge effects and investigate. the most critical conditions and others have been disregarded. the most critical portions of the structure.

Normal pressures acting over the surface If the maximum stresses are below the yield of the cylindrical shell are conveniently re- stress of the material, then the structure has f 66