— AMCP 706-286 — Engineering Design Handbook (1963) (EN)

Downloaded from https://www.everyspec.com DESIGN CONSIDERATIONS sumcient yield strength. To check the vlti- Stictly speaking, the stiffness criterion is mate strength, the analyst multiplies the not directly related to the strength of a struc- limit loads by a factoi- of safety and goes ture. A stiffness criterion on a structurc ,or through the stress calculation.

The maximum structural component may be establIshed be- str&sses must c=erywhere be less than the cause too much flexibility of the structure ultimate stress of %he material mi.r In-erfere with the proper operation of Should the yield stress of the material be the control system, er may seriously affect exceeded under limit loads, or the ultimate tte stability and control characteristics of stress exceeded under ulfiPate loads, then the mixўle. Consider the design of control the structure is obviously too w-Pak and the Unkage systems and their supports. it is design must be strengthened.

One of the obvious that if the supports were attached to most straight-forward measures that can he a very flexible structure, the supports would taken by the designer is to increase the cross- fall out of line under the appEed loads and sectional arsa suffici nly that the maximum could :ender the control system inoperable. stresses are reduced below the yield or ulti- The same would be true if the control shaft mate strength criterion, depending upon itself were to deflect transversely between which one is critical. In the case of tic thin- supports.

To insure the proper o eration of walled circular cylinder, the designer iamy such control syctems, the design is governed increase the wall thickness. This solution, of by a stiffness criterion course, adds weight to the structure which A number of other examples may be cited. may well be intolerable. The designer may It is ixrportant to consider the relative defor- then consider another alloy of the same mation between the sensing instrument, say material with higher yield and ult;mate in a stabilization system, and the control sur- strengths. This may give a satisfactory solu- face.

If too much twisting or bending of the ion, prcvided that no trouble is anticipated structure occurs between tLe location of the due to increased cust. manufacturing difficul- sensing equipment ard the control surface, ties, the possibility that the material is toe the desired stabilization may not be achieved. brittle, and other considerations. The de- It is also possible to adversely affect the sta- signer may also investigate the desirability bility derivatives of a missile if there is ex- of altering the structuralconfiguration or the cessive deformation in bending, or control -__e of another material efctiveness may be impaired if a control 4-5L .21RU ICTU .

TI1ES$ surface does not have suif ;ient torsional stiff- Anes. The important point that -must be borne A measure of the stiffness of a structure in mind is that rigidity requirements are im- is the product of Young's Modulus of the portant conisiderat.ans in the design of a mis- material and the geometry of the cross-sec- sile and some of its components. tion, namely the moment of inertia. This pro- There are instances in which a rigidity duct, EI, is called the bending rigidity. Tor- requirement is imposed in order to safeguard sional rigidity, GC, is also the product of a the integrity of a structure.

Under some material elastic constant and the cross-sec- flight conditions, the aerodynamic fcrces may tion. G is the Modulus of Rigidity and C is vary in resonance with the natural frequency a property only of the cross-section. For of the structure which in turn is a function solid or tubular cross-sections, C is the polar of the structures stiffness and mass distribu- moment of ineria of the section. The stiff- tion. This resonance can lead to catastrophic necs of a structural element is also affected failure. Interaction: between aerodynamic, by.the magnitude and type of load to which elastic, and inertia forces are called aero- it is subjected. Compressive loads tend to elastic ,.flects.

The speed at which these decrease the effective stiffness of a structural forces resonate is called the flutter speed and element, whereas tensile loads have the oppo- the phenomenon is called flutter. The com- site effect. ponents of a missile that are most apt to 67