— AMCP 706-286 — Engineering Design Handbook (1963) (EN)

Downloaded from https://www.everyspec.com STRUCTURES flutter are the control surfaces. Individual additional oscuflating loads on the fin s panels of a structure may also flutter under po rtpoints and thereby creating the possi- the proper conditions. bility of fatigue filure. The above considerations are very impor- The problems associated with vibratory tant and the aeroalastician must calculate loads are more in the nature of their effect the flutter speed to insure that it is well above on the performance of the missile rather than V the speeds expected to be encountered. The with the strength or integrity of the struc- analytical compatations cannot be performed tural cpmponent.

A vibrating panel could until the design has progressed sufficiently to conceivably affect the aerodynamic behavior enable the analyst to determine the elastic of the missile. At times the problem is assc-. resistace and mass distribution of the struc- ciated with the proper functioning of elec- tur& Aerodynamis and structural damping tronic equipment or with .acoustical trans- are usually included in the analytical formu- missiom. There are also ,other problems lation of the problem.

Once the missile has created by the vibratory loads, some of which been constructed, an experimental chec1& can may be of greater concern to some designers be made of the structural stiffness by than those mentioned above. Having noted statically loading the member or missile and that fatigue is not the important considera- observing the deflections a.d slopes, or by tion, but rather one of interaction with other forced vibration tehnique bv which the phaass of the missile design. the question stiffness can be deduced from the amplitude raised is in connection with the step3 that and frequency response of the structure.

the structural designer can take to alleviate it may also be worthwhile to mention that the undesirable conditions. liquid sloshing and liquid impact against One obvious method of approach is toelim- bulkheads P.t thrust cut-off may affect rigid- inate the vibratory forces at their source. I ity requdrements of certain structul corn- This cannot always be accomplished. How- ponents. ever, if the source of the virbatory loads can 4-53° Fatigue. The design of a structure be traled to -the engine, or if vibrations occur for vibratory loadv is a source of wr.jor con- in transit aid storage, a shock mounting cern for all missile structural designers, A technique may be effective.

In other cases, vibratory load on v, eructural elemet im- the designer must seek to increase the 3tiff- mediately gives r!K to the possibility of - ness of the strciure or portion of the stru - ure by fatigue. For flight vehicles that are -2:e which is involved. Inasmuch as the designed to last (in principle) an indifinitely structural stiffness is proportional to Ahe long time, the possibility of fatigue failure rroduct of Young's Modulus (or the mo'duius is important and always inv.stigated.

For of rigidity) and the geometry of the cro.s- ballistic missiles, however, the relatively section, the designer can either choose a nev short life duration usually precluleb 'he pQs- material with a higher Young's Modulus, or sibility of fatigue failure. Fatigue faiiure he can change the cross-section. Changing should be investigated in a missile design, the cross-section to increase the stiffness can but it is generally not important as a design be achieved by altering the configuration consideration. without increasing the area, or by increasing An example under which a ballistic missile the area. may be subject to fatigue failure can be 4-5.4. Buckling. She. r etresses and normal cited.

A ballistic missile is erected on its compressive stresves v_--ng on thin-walled launching pad in such a manner that the elements give risc to tl possibility of buck- stand load is introduced at the tips of the ling. Fortunately, buckling of a curved two- fins. The missile may remain in this position dimensional thin-wall element requires a for a relatively long time. At a particular stress which is much higher than the buck- speed, lateral winds passing over the fins ling stress of a flat elemeat. The buckling way cause the fins to resonate, introducing strese of a square fiat plate simply supported ( 68