US Army Materiel Command AMCP 706-341 — Engineering Design Handbook — Carriages and Mounts Series: Cradles (EN)

Downloaded from https://www.everyspec.com ) and fits concentrically around the gun tube. reinforcement of the structure may be neces- The internal elements of the recoil mechanism sary to carry the load. fit between outer diameter of the gun tube and 20. The method for calculating the approx- inner diameter of the cradle. Due to the corn- imate recoil force is found in Reference 2. pactne-s of the assembly, this type cradle is This force comprises the sliding frictional usually found in tanks where space is at a resistance of the recoiling parts and the resist- premium. A big advantage offered by this ance provided by the recoil mechanism.

type is that the recoil mechanism is on the axis Sketches in Figure 5 show how the applied of the gun bore which is also the line of action loads and corresponding recoil force are dis- of the recoiling parts and can readily be made tributed on the U-type and O-type cradles. the location of the trunnions. Consequently, Figure 5a has those of a single recoil syztem reactions to the moments at the trunnion and Figure 5b has those of a double recoil bearings are negligible. Frictional forces are system. The definitions of the symbols in minimal, produced only by the normal corn- Figure 5 follow. ponent of the weight of the recoiling parts.

CG = the center of gravity of the recoiling parts F,, = inertia force of the recoiling parts in a IV. DESIGN PROCEDURES single recoil system, or of the primary recoiling parts in a double recoil system A. STRUCTURE TO CARRY THE VARIOUS FORCES F, = propellant gas force 18. In its role of supporting structure for the F, = inertia force of primary recoiling parts other tiping arts , ro e c e si subcted o te due to secondary recoil acceleration other tipping parts, the cradle is subjected to a = frictional resistance of front bearing number of forces which it must transmit to the i, = frictional resistance of rear bearing carriage.

The predominant one is the recoil Kit = force provided by recoil mechanism force. Others include the equilibrator force, R, = normal reaction of front bearing the elevating gear reaction due to tipping R 2 = normal reaction of rear bearing moments, and the reaction on the key or W 1 = weight of recoiling parts in a single re- guides due to the rifling torque. During the coil system or of the primary recoiling early stages of design, approximate loads are parts in a double recoil system adequate and are readily available. When the 0 = angle of elevation design is in its final stages, the loads should be K - total resistance to recoil (recoil force) accurate.

However, first approximations, in all likelihood, will be close enough to the final = of friction values sothat only minor revisions in the struc- ,= R (la) ture will be necessary. h uR2 (1b) K =Ku +fi+f2 (2) F. F,,+-t- Wsin 0-K- F, cos 0 (3) 1. Recoil Attachment to the Cradle The force F, occurs in double recoil systems 19. When the recoil mechanism housing is where integral with the cradle, the recoil forces are W, applied through it and no additional support- F, = a2 = m 1 a2 (4) ing structure is necessary.

If it is merely at- g tached to the cradle, appropriate yokes or sim- and the acceleration of the secondary recoiling ilar structures are needed to carry its force to mass is the cradle. If the recoil mechanism is at- F2 tached to and moves with the recoiling parts, a2= (5) the recoil rod is fixed to the cradle, sometimes 2 by an adapter or sometimes by a nut threaded F2 K cos 0 - W, cos 0 sin 0- R to the end of the rod. The rod, in this case, is 1 + (M/Mr) sin0 (6)* attached to the front of the cradle where local * Obtained from Reference 2, Equation 88. 5V