US Army Materiel Command AMCP 706-341 — Engineering Design Handbook — Carriages and Mounts Series: Cradles (EN)

Downloaded from https://www.everyspec.com 1) the above loads are determined as shown in S/ 0.6 X 100,000 Paragraph 66. = 28,700 = 2.09 4. Trunnion Loads Ab, = 4.5 X 0.375 = 1.6875 in2, bearing area 88. The trunnion reactions, FA and FN, are , = - = 57,400 lb/in2, bearing stress found by summation of forces parallel and perpendicular to the center line of the bore The cradle material has the lesser strength. (Figure 8). At a yield of 60,000 lb/in 2 FN = Fgsin (0 - X) + R, cos (0 + 0 + ) 1.4 x 60,000 1.46 - W cos 0 - W, cos 02 Sf = 57,400 = 10,000 + 3700 - 5000 - 3500 90. The trunnion bearings are based on the = 5,200 lb loads that are present when the rifling torque FA = F, - F.

+ W, sin 0 + W sin .2 is maximum. This is the only condition to be + Fg cos (0 - X) + R, sin (0 + 0 + ,Y) investigated here. Other conditions may be = 1,810,000 - 1,668,700 + 8700 + 2000 more critical and should be checked. From + 37,200 + 4400 = 193,600 lb Paragraph 74 89. The maximum load on the trunnion F, = 19,500 lb housing bolts is applied when the rifling From Paragraph 88 torque is maximum.

FN =5200 lb T, = 545,000 lb-in (see Paragraph 74) FA = 193,600 lb F,' = l = 29,400 lb Maximum trunnion load 18.5 ) FN2- = 2600 lb Fr = -+- + F = 100,000 lb 2 2 = 2 2+ FA- 19,0 = 96,800 lb FA 1 0- 9The trunnion bearing load of the single With reference to Figure 31, the maximum recoil type is over 45 per cent morm than that bolt load is for the double recoil type illustrating one ad- vantage of having the latter type system (see 5.8 FA 1 F , Paragraph 74). The remaining analyses of R X 18 2 2 \ T - ) trunnion and hub follow procedures similar to = 31,200 + 13,400 = 44,600 lb those of Paragraphs 74 through 76. 91.

The reactions produced by the rifling There are four 5/8-11 NC bolts at R; torque are transmitted directly from the slides A 4 X 0.202 = 0.808 in' , total root area to the trunnion housing and therefore do not enter into the analysis of the (U-shaped) R; primary cradle structure. All the remaining A - 55,300 lb/in 2 , tensile stress normal and axial loads and reactions are con- 100,000 sidered. With reference to Figures 31 and 32, S - =000 = 1.81 the total reactions now become 55,300 = FA R 8 F.A - 62,400 - 2600 59,800 R -- 2 = 96,800 lb, key load 18 A A. = 4.6 X 0.75 = 3.375 in 2 , shear area R, = 1 FA+ 1 F, = 65,000 lb . =28,700 lb/in 2 , shear stress 18 FA +2 A. R. = F 1 193,600 lb 37 V