2. Programming Concepts 2-17 OFF STOP RUN Special ES2 SA2 Latch Function SS2 SX2 Attrib. Default M EX2 SE -ed ON RUN STOP M1208 C208 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1209 C209 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1210 C210 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1211 C211 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1212 C212 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1213 C213 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1214 C214 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1215 C215 counting mode (ON:
count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1216 C216 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1217 C217 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1218 C218 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1219 C219 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1220 C220 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1221 C221 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1222 C222 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1223 C223 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1224 C224 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1225 C225 counting mode (ON:
count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1226 C226 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1227 C227 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1228 C228 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1229 C229 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1230 C230 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1231 C231 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1232 C232 counting mode (ON: count down) ╳ ○ ╳ ╳ OFF - - R/W NO OFF C232 counter monitor (ON: count down) ○ ╳ ○ ○ OFF - - R NO OFF M1233 C233 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1234 C234 counter monitor (ON:
count down) ○ ○ ○ ○ OFF - - R NO OFF M1235 C235 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1236 C236 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1237 C237 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1238 C238 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1239 C239 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1240 C240 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1241 C241 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1242 C242 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1243 C243 Reset function control.
ON = R function disabled ○ ○ ○ ○ OFF - - R/W NO OFF M1244 C244 Reset function control. ON = R function disabled ○ ○ ○ ○ OFF - - R/W NO OFF M1245 C245 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1246 C246 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1247 C247 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1248 C248 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1249 C249 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1250 C250 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1251 C251 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1252 C252 counter monitor (ON:
count down) ○ ○ ○ ○ OFF - - R NO OFF M1253 C253 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1254 C254 counter monitor (ON: count down) ○ ○ ○ ○ OFF - - R NO OFF M1257 Set the ramp up/down of Y0, Y2 to be “S curve.” ON = S curve. ○ ○ ○ ○ OFF OFF - R/W NO OFF M1260 Set up X7 as the reset signal for software counters C235 ~ C241 ○ ○ ○ ○ OFF - - R/W NO OFF M1262 Enable cyclic output for table output function of DPTPO instruction. ON = enable. ○ ○ ○ ○ OFF OFF - R/W NO OFF M1270 C235 counting mode (ON: falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF M1271 C236 counting mode ON: falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF