DVP-ES2/EX2/SS2/SA2/SX2/SE&TP Operation Manual - Programming 2-18 OFF STOP RUN Special ES2 SA2 Latch Function SS2 SX2 Attrib. Default M EX2 SE -ed ON RUN STOP M1272 C237 counting mode (ON: falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF M1273 C238 counting mode (ON: falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF M1274 C239 counting mode (ON: falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF M1275 C240 counting mode (ON: falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF M1276 C241 counting mode (ON: falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF M1277 C242 counting mode (ON:
falling-edge count) ○ ○ ○ ○ OFF - - R/W NO OFF M1280* For I000 / I001, reverse interrupt trigger pulse direction (Rising/Falling) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1284* For I400 / I401, reverse interrupt trigger pulse direction (Rising/Falling) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1286* For I600 / I601, reverse interrupt trigger pulse direction (Rising/Falling) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1303 High / low bits exchange for XCH instruction ○ ○ ○ ○ OFF - - R/W NO OFF M1304* Enable force-ON/OFF of input point X ○ ○ ○ ○ OFF - - R/W NO OFF M1305 Reverse Y1 pulse output direction in high speed pulse output instructions ○ ○ ○ ○ OFF OFF - R/W NO OFF M1306 Reverse Y3 pulse output direction in high speed pulse output instructions ○ ○ ○ ○ OFF OFF - R/W NO OFF M1307 For ZRN instruction, enable left limit switch ○ ○ ○ ○ OFF OFF - R/W NO OFF M1308* Output specified pulses or seek Z phase signal when zero point is achieved.
○ ○ ○ ○ OFF OFF OFF R/W NO OFF M1312 For COM1(RS-232), sending request (Only applicable for MODRW and RS instruction) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1313 For COM1(RS-232), ready for data receiving (Only applicable for MODRW and RS instruction) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1314 For COM1(RS-232), data receiving completed (Only applicable for MODRW and RS instruction) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1315 For COM1(RS-232), data receiving error (Only applicable for MODRW and RS instruction) ○ ○ ○ ○ OFF OFF - R/W NO OFF M1316 For COM3(RS-485), sending request (Only applicable for MODRW and RS instruction) ○ ╳ ○ ╳ OFF OFF - R/W NO OFF M1317 For COM3(RS-485), ready for data receiving (Only applicable for MODRW and RS instruction) ○ ╳ ○ ╳ OFF OFF - R/W NO OFF M1318 For COM3(RS-485), data receiving completed (Only applicable for MODRW and RS instruction) ○ ╳ ○ ╳ OFF OFF - R/W NO OFF M1319 For COM3(RS-485), data receiving error (Only applicable for MODRW and RS instruction) ○ ╳ ○ ╳ OFF OFF - R/W NO OFF M1320* For COM3 (RS-485), ASCII/RTU mode selection.
(OFF: ASCII; ON: RTU) ○ ╳ ○ ╳ OFF - - R/W NO OFF M1334* Close the conditional contact and to enable the instructions PLSR, DPLSR Y0, DDRVI, DDRVA CH0(Y0/Y1) to execute ramp-down (ON: Enable; OFF: Disable) (available for ES2/EX2: V3.42, ES2-C: V3.48, ES2-E: V1.00, SS2: V3.28, 12SA2: V2.86, 26SE: V2.0, SX2: V2.86, 28SA2: V3.0 or later) ○ ○ ○ ○ Off - - R/W NO Off M1335* Close the conditional contact and to enable the instructions PLSR/DPLSR ○ ○ ○ ○ Off - - R/W NO Off