Table 1: FRM (Field Replaceable Module) List Part No. CQ114-90035 Rev B HP Scitex FB500 / FB700 Service Manual Page 15 of 510 Part # Part Name Type Description Page 0603114 FUN- NEL,32 OZ,6.5" TOP OD _ _ _ ,0.625" SPOUT OD,HDPE _ _ OHS This is the funnel to facilitate emptying ShopVac waste ink into waste ink bottle 0900710 FRM,BLT,CARRDRV TIMN _ G,MXABCDHIJ Carr Drv This is the carriage-drive timing belt between the carriage-drive motor and the carriage-drive shaft. page 262 0901389 FRM,MTR CNTRL BRD,L _ _ Elec This is the motor control board (a.k.a. motor driver board) in the electronics assembly. Common to 500-700, FB910, FB950.
page 368 0901400 FRM,BLWR,BLT VAC,L _ Maint This is the belt vacuum blower assembly used to suck down the media to the belt. This includes one blower. Common to 500-700, FB950, FB910. page 309 0901402 FRM,ALGN PIN ASSY,L _ _ Med Drv Alignment pins or N-up pins. These pins used to set the position of multiple sheets. Multiple instances are used on the printer; this FRM is for qty. 1. Common to 500-700, FB950, FB910. 0901405 FRM,PRNTER LVLING PAD _ _ ,L Encl This is the leveling pad for FB500, FB700, FB950 and FB910 (CS9840). 0901406 FRM,MEDIA THKNSS SN _ _ SR,L Med Drv This is the media thickness sensor assembly for FB950, FB910, FB500, FB700. It was calibrated in the factory.
page 327 0901407 FRM,MEDIADRV ENCDR,L _ Med Drv This is the encoder that attaches to end of the media-drive motor on the service end of the printer. Common to 500-700, FB950, FB910. This is not the hi-resolution encoder located on the user end of the printer (the type & location varies by the printer model). page 288 0901425 FRM,RLD E STRP&FM,ABC _ _ DHIJ Carr Drv This is the mylar encoder strip (and foam tape) that is installed in the full length of the rail. It is long enough for a 98"/2.5m printer and can be trimmed down for smaller printers. This FRM requires you to reuse the existing aluminum bar from the old strip.
page 264 0901469 FRM,ON OFF SW,L _ _ Elec This is the On/Off switch on the electronics assembly. Common to 500-700, FB950, FB910. 0901507 'FRM,SPLY,UV POWER,DU _ AL CH,N _ Elec This is the UV Power Supply for FB500. Also used in some models of the H-Series or CS5400 printer. Check control panel System Information; if panel shows "NDP", order this FRM. The FRM is a single unit that powers both channels. See CQ115-67004 for the FB700 UVPS. page 379 0901512 FRM,PWR DIST BRD,N _ _ Elec This is the power distribution board for FB500, FB700, and H- Series. This routes inbound AC to the various printer power sup- plies.
page 378 0901513 FRM,FAN,EBOX,COOL- ING,N Elec This fan assembly cools the electronics box in the printer. The elec- tronics box has three of these (fans) in it. Two are exhaust and one is intake. page 392 0901533 FRM,MTR,SRV STN,N _ Maint This is the service station wiper motor (which moves the wiper head in the Y axis). Common to 500-700, FB950, H-Series. page 399 0901561 FRM,S&T MOTOR&SWITC _ HES,L Med Drv This is the takeup motor and switch assembly for the roll-to-roll accessory. Common to 500-700, FB910, FB950. page 348 0901572 KIT,TOOL,BELT TENSION,L _ Med Drv This is the custom HP tool/fixture used to measure and set tension on the media belt.
A dial indicator (not included, see CQ114- 67176) is required to use this tool. Applicable to 500-700, FB950, FB910. This tool and a dial indicator are mandatory tools for all service that involves changing the belt tension. page 288