D.4 User Setting Table D.4 User Setting Table Standards Compliance SIEP C710606 33A OYMC AC Drive – J1000 User Manual 221 D No.
Name User Setting A1-01 Access Level Selection A1-03 Initialize Parameters A1-04 Password 1 A1-05 Password 2 b1-01 Frequency Reference Selection 1 b1-02 Run Command Selection 1 b1-03 Stopping Method Selection b1-04 Reverse Operation Selection b1-07 Local/Remote Run Selection b1-08 Run Command Selection while in Programming Mode b1-14 Phase Order Selection b1-17 Run Command at Power Up b2-02 DC Injection Braking Current b2-03 DC Injection Braking Time/DC Excitation Time at Start b2-04 DC Injection Braking Time at Stop C1-01 Acceleration Time 1 C1-02 Deceleration Time 1 C1-03 Acceleration Time 2 C1-04 Deceleration Time 2 C1-09 Fast-Stop Time C2-01 S-Curve Characteristic at Accel Start C2-02 S-Curve Characteristic at Accel End C2-03 S-Curve Characteristic at Decel Start C2-04 S-Curve Characteristic at Decel End C3-01 Slip Compensation Gain C3-02 Slip Compensation Primary Delay Time C4-01 Torque Compensation Gain C6-01 Duty Mode Selection C6-02 Carrier Frequency Selection C6-03 Carrier Frequency Upper Limit C6-04 Carrier Frequency Lower Limit C6-05 Carrier Frequency Proportional Gain d1-01 Frequency Reference 1 d1-02 Frequency Reference 2 d1-03 Frequency Reference 3 d1-04 Frequency Reference 4 d1-05 Frequency Reference 5 d1-06 Frequency Reference 6 d1-07 Frequency Reference 7 d1-08 Frequency Reference 8 d1-17 Jog Frequency Reference d2-01 Frequency Reference Upper Limit d2-02 Frequency Reference Lower Limit d3-01 Jump Frequency 1 d3-02 Jump Frequency 2 d3-04 Jump Frequency Width d4-01 Frequency Reference Hold Function Selection E1-01 Input Voltage Setting E1-03 V/f Pattern Selection E1-04 Max Output Frequency E1-05 Max Voltage E1-06 Base Frequency E1-07 Mid Output Frequency E1-08 Mid Output Frequency Voltage E1-09 Minimum Output Frequency E1-10 Minimum Output Frequency Voltage E2-01 Motor Rated Current E2-02 Motor Rated Slip E2-03 Motor No-Load Current No.
Name User Setting E2-05 Motor Line-to-Line Resistance H1-01 Multi-Function Digital Input Terminal S1 Function Selection H1-02 Multi-Function Digital Input Terminal S2 Function Selection H1-03 Multi-Function Digital Input Terminal S3 Function Selection H1-04 Multi-Function Digital Input Terminal S4 Function Selection H1-05 Multi-Function Digital Input Terminal S5 Function Selection H2-01 Terminal MA, MB and MC Function Selection (relay) H3-01 Terminal A1 Signal Level Selection H3-03 Terminal A1 Gain Setting H3-04 Terminal A1 Bias Setting H3-13 Analog Input Filter Time Constant H4-01 Multi-Function Analog Output (Terminal AM Monitor Selection) H4-02 Multi-Function Analog Output (Terminal AM Output Gain) H4-03 Multi-Function Analog Output (Terminal AM Output Bias) H5-01 Drive Node Address H5-02 Communication Speed Selection H5-03 Communication Parity Selection H5-04 Stopping Method After Communication Error H5-05 Communication Fault Detection Selection H5-06 Drive Transmit Wait Time H5-07 RTS Control Selection H5-12 Run Command Method Selection H5-13 MEMOBUS Frequency Reference and Frequency Monitor Unit L1-01 Motor Overload Protection Selection L1-02 Motor Overload Protection Time L1-13 Continuous Electrothermal Operation Selection L2-01 Momentary Power Loss Operation Selection L3-01 Stall Prevention Selection during Accel.
L3-02 Stall Prevention Level during Accel.
L3-04 Stall Prevention Selection during Deceleration L3-05 Stall Prevention Selection during Run L3-06 Stall Prevention Level during Run L4-01 Speed Agreement Detection Level L4-07 Frequency Detection Conditions L5-01 Number of Auto Restart Attempts L6-01 Torque Detection Selection 1 L6-02 Torque Detection Level 1 L6-03 Torque Detection Time 1 L8-01 Internal Dynamic Braking Resistor Protection Selection (ERF type) L8-05 Input Phase Loss Protection Selection L8-10 Heatsink Cooling Fan Operation Selection L8-12 Ambient Temperature Setting L8-18 Soft CLA Selection L8-35 Side-by-Side Selection L8-38 Carrier Frequency Reduction n1-02 Hunting Prevention Gain Setting n3-13 Overexcitation Deceleration Gain o1-02 User Monitor Selection After Power Up o1-03 Digital Operator Display Selection o2-02 STOP Key Function Selection