B-Series Camera Setup Guide — Omron Mounting & Connection (EN)

How to use the Guide 1. The Table of Contents is hyperlinked for ease of use. Hold the control button and click the page number or title of the desired section to be read. 2. Each section of this guide can be expanded or collapsed. Right click on the title of a section and select collapse all headings. The contents of the guide can then be individually expanded or collapsed as needed. Additionally, by hovering the mouse over the left hand side of a section title, a triangular icon will appear that can be clicked to expand or collapse that particular section. 3. Double click on the icon to open embedded documents. Omron Automation | © 2022 Omron. All Rights Reserved. | omron.automation.com 2

Стр. 2

Table of Contents Contents How to use the Guide ............................................................................................................................ 2 Table of Contents .................................................................................................................................. 3 Guide Objective and Terminology ......................................................................................................... 4 Warnings ................................................................................................................................................

4 Mount the Camera ................................................................................................................................. 4 Install a Lens .......................................................................................................................................... 5 Connect the Ethernet Cable and I/O Cable ........................................................................................... 7 Connect the Power Supply ..................................................................................................................

13 Download and Install the SDK Software .............................................................................................. 14 Set up PC IP Settings .......................................................................................................................... 15 Launch the B-Series Software ............................................................................................................. 16 Camera Configuration ..........................................................................................................................

17 Acquire an Image ................................................................................................................................. 17 Omron Automation | © 2022 Omron. All Rights Reserved. | omron.automation.com 3

Стр. 3

Guide Objective and Terminology This guide covers all of the steps required to connect a B - Series camera to a PC and configure the camera for usage. For information related to the B - Series, refer to the applicable B - Series manual. 21S012-00_STC-BxS 500xx-BC_Spec_Man 21S013-00_STC-BxS 312xx-Bx_Spec_Manu 21S014-00_STC-BxS 43xx-Bx_Spec_Manua 21S041-00_STC-BxS 202xx-Bx_Spec_Manu 21S042-00_STC-BxS 163xx-Bx_Spec_Manu 21S064-00_STC-BxS 213xx-Bx_Spec_Manu 21S075-00_STC-BxS 1242xx-BC_Spec_Man 21S076-00_STC-BxS 2041xx-BC_Spec_Man Warnings 1. Sensor temperature must be maintained less than the maximum sensor temperature listed in the applicable manual.

To ensure this, keep the StViewer “Mainboard” temperature, also called chunk data “Camera temperature”, at the (sensor limit - 10°C) 2. Forced air cooling or additional heatsinking must be used if the ambient temperature is >25°C Mount the Camera To mount the camera use one of the following methods: 1. Attach the B-Series camera to your equipment using either the M3 or M2 mounting holes on the camera. Ensure that your mounting screws do not exceed the allowable depths of 4mm for the M4 holes and 3.5mm for the M2 holes. Refer to the specific diagram in the manual for your part number. Omron Automation | © 2022 Omron. All Rights Reserved. | omron.automation.com 4

Стр. 4

Install a Lens In order to use a B-Series camera a lens must be installed. The camera is designed to use standard C-mount lenses. For more information on the available C-mount lenses see the Vision Accessory Catalog. Vision Accessory lens calculations How to select a Catalog.pdf template-5.xlsx lens.pdf Refer to the applicable B-Series camera datasheet, to determine the camera’s sensor size and resolution. Choose a lens family, which is appropriate for the resolution and sensor size, using the Vision Accessory Catalog as a guide. Calculate the required lens focal length to attain the correct field of view. The training “How to Select a Lens” may help ion the calculations.

To attach the lens screw the lens on to the camera. Torque should be “hand tight”. Omron Automation | © 2022 Omron. All Rights Reserved. | omron.automation.com 5

Стр. 5