NERLITE Smart Series Pharmalite Illuminator Configuration Guide (EN)

NERLITE Smart Series Pharmalite Illuminators Configuration Guide Hardware Required P/N 83-230019-02 Rev C Part Number Description Continuous Current Strobe Current Continuous Mode Continuous Mode with Dimming Or On-Off Control High Output Strobe Mode No Controller Required (Can be connected directly to 24VDC) No Controller Required (Can be connected directly to 24VDC) No Controller Required (Can be connected directly to 24VDC) 98-000228-01 Smart Series Pharmalite 160 mA 850 mA Figure A or D Figure B (or D for On-Off Control only) Figure C 98-9000137-01 Smart Series Pharmalite for HAWK MV-4000 160 mA 850 mA Figure A or D Figure B (or D for On-Off Control only) Figure C Item Description Part Number 1 Smart Series Pharmalite 98-000228-01 1 Smart Series Pharmalite for HAWK MV-4000 98-9000137-01 2 Power Supply DSP60 24VDC 2.5A DIN Mount NER-011504100 2 Power Supply DSP100 24VDC 4.2A DIN Mount 97-000006-01 3 Cable 5-Pin M12 Female-to-Flying Leads, 3 M 61-000186-01 3 Cable 5-Pin M12 Female-to-Flying Leads, 5 M 61-000187-01 4 Cable, Power Smart Series to QX-1 Continuous 61-000204-01 4 Cable, Power Smart Series to QX-1 On/Off 61-000207-01

Стр. 1

NERLITE Smart Series Pharmalite Illuminators Accessories Connections: Continuous On/Off Dimming Strobe Control Signals DIM (Continuous Mode with PWM Dimming): 0VDC (LEDs off) to 3.1-3.5VDC (LEDs on) pulse width modulated (PWM) signal , Note: When using Continuous Mode with Dimming, the LED duty cycle will equal the duty cycle of the dimming signal. DIM (Continuous Mode with On/Off Control): 0VDC (LEDs off), 3.1-3.5VDC (LEDs on), ( TRIG (High Output Strobe Mode): Optoisolated, 0VDC (LEDs off) to 3.1-28.8VDC (LEDs on), 10mA max, 20 μs min Trigger pulse width. Note: High Output Strobe internally limits LED frequency and pulse width to a maximum of 90Hz and 1 ms respectively.

Light output pulse will follow Trigger pulse width from 20 μs to 1 ms. Note: When using Continuous Mode with Dimming, the LED duty cycle will equal the duty cycle of the dimming signal. Cable Specifications: Wire colors for flying lead cables: Pin 1 = Brown Pin 2 = White Pin 3 = Blue Pin 4 = Black Pin 5 = Gray Connector Nut = Shield Note: Non-Omron Microscan cables may use different wire colors. It is the customer’s responsibility to make sure the light is connected correctly per the pin numbers in the table above. Copyright ©2019 Omron Microscan Systems, Inc.

www.microscan.com Description Part Number Application AC Power Cord US NER-030028300 Power Cord For Power Supply AC Power Cord EU NER-030028400 Power Cord For Power Supply AC Power Cord UK NER-030028500 Power Cord For Power Supply Input Connector (M12 Male, 5 Circuit, A-Code) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Backshell Continuous Mode (Figures A & D): +20.2-28.8VDC DC GND DC GND +20.2-28.8VDC No Connection Shield Continuous Mode With Dimming (Figure B): +20.2-28.8VDC DC GND DC GND & DIM (-) +20.2-28.8VDC Dim (+) Shield Continuous Mode With On-Off Control (Figure B): +20.2-28.8VDC DC GND DC GND & DIM (-) +20.2-28.8VDC Dim (+) Shield High Output Strobe Mode (Figure C):

+20.2-28.8VDC TRIG (-) DC GND TRIG (+) No Connection Shield

Стр. 2