No. 600 Prices Pounds Sterling Carriage Extra Issued December 2002 Section 2 Chuck Guards / Collets / Adaptors 7 Series 10 Series 7 254 Part No. Description Price Excl. VAT £ Price Incl.
VAT £ Chuck guard accommodates both 3 and 4 jaw - swings clear to provide ready access for loading and unloading 30/023 Chuck guard assembly - single point fixing - for existing machines 43.35 50.93 30/051 Additional guarding to give extra enclosure for changewheel guard and backgearing - for existing machines 17.40 20.44 30/022 Chuck guard assembly - single point fixing - for existing machines 42.94 50.45 80023 Transparent safety shield with magnetic base for cross-slide or bed mounting; the tough acrylic screen 254mm x 190mm (10 x 71/2) provides safe vision with protection from flying chips and coolant 58.43 68.65 11445 Collets No.
2 M.T., these collets are available in 1/2mm increments in sizes 2mm to 13mm and from 1/16 to 1/2 in 64th increments 18.00 21.15 95/085 Collet adaptor for 11445 (with draw tube adaptor securing) 59.70 70.14 1438 Nose piece, to enable 11445 collets to be fitted directly into headstock spindle 14.95 17.56 1439 Collet closing tube:
comprising 14367 Extractor and 11446 Knob; this is intended for closing the collet to simplify insertion into, or removal from, the nose piece 10.40 12.22 11554 Collet case, polished hardwood, holds 16 collets, plus nose piece and collet closing tool (case only) 26.20 30.79 20/065F Lever operated collet chuck has all components hardened and ground.
It is of the backplate mounting type so that if ordered subsequently for an existing machine the backplate can be finished in position on the lathe thus giving the maximum possible degree of concentricity 322.37 378.78 A7821 Collets for use with 20/065F, they are of the “dead length” type and are available in 1/2mm increments in sizes 2mm to 16mm and 1/16 to 5/8 in 64th increments 23.87 28.04 95/111 Lever operated collet chuck, for lathes fitted with standard BS3331 spindle (To order only) 983.20 1155.26 95/128 Lever operated collet chuck, for lathes fitted with 3 Camlock D1 spindle (To order only) 983.20 1155.26 95/112 Standard 163E dead length collets for use with 95/111 and 95/128 lever operated collet chucks.
They are available in 32nd increments in sizes 2mm to 30mm and also 1/8 to 11/8 in 32nds (To order only) 41.17 48.37 95/112 Sizes 2mm, 2.5mm, 1/16, 3/32 (To order only) 53.12 67.87 95/113 Rubberflex 2428/Series 24 collets for collet chucks 95/111 and 95/128. 12 in full set, covering all sizes from 6mm to 30mm. Each collet covers 2mm spread of sizes, e.g. 6-8mm, 8-10mm, etc 57.77 67.87 N.B. 95/111 and 95/128 spindle bored to clear 25mm (1) 14542 Blank arbor measuring 50mm x 44mm dia. (2 x 13/4 dia.) with ground 2 M.T. shank.
The shank has been left soft so that it can be drilled and tapped for a draw bar 8.60 10.10 14656 Straight shank adaptor, with a thread at the front end with register to match the thread and register on the headstock spindle. (Ideally suited for mounting your threaded body chuck onto a rotary table, or mill two flats and you can hold a chuck in your bench vice.) 9.44 11.09 70/1967/1 Adaptor for mounting headstock chucks etc, on tailstock. This has a 2 M.T. shank and a thread at the front end with a register to match the thread and register on the headstock spindle nose 10.90 12.80