Seres user manual (EN)

IMPORTANT SAFETY INFORMATION SPEAKER PLACEMENT 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other ap­ 1. The two satellite speakers should be positioned on each side of your computer monitor. To wall mount, the pedestal stands may be removed by unscrewing the 1/4” 20-thread bolt, which accommodates a wide variety of wall brackets available through stereo and appliance stores.

2. Place the subwoofer under your computer desk. The subwoofer must be placed on the floor near a wall with the rear panel toward the wall. Do not cover up the sub driver or front port of the enclosure and be sure to provide enough ventilation to the rear of the subwoofer. It is normal for this panel to be warm to the touch. The subwoofer should be at least 3 feet (1m) from the computer monitor to avoid interference. 3. Speaker or power cables running across an area of heavy foot traffic should be paratus (including amplifiers) that produce heat. 9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer. 12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, positioned against a wall or corner and secured with tape. SPEAKER CONNECTION DIAGRAM 1.

Do not plug in the AC power cord until your computer/audio system is set up. 2. Connect mini plug to PC soundcard from the control satellite preamp. Care or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus should be advised concerning the cables at back of sub. Bumping them could cause damage. 3. Connect the DIN plug to the sub from the control satellite preamp. 4.

Connect the speakers by inserting the tinned wire leads into the subwoofer. has been damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled, objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus. 16. To completely disconnect this apparatus from the AC mains, disconnect the power supply cord The solid black wires (-) connect to the black spring clips; the black wires with red stripes (+) to the red spring clips. 5.

Plug the AC power cord into a wall outlet. 6. Plug headphone mini stereo plug in headphone jack, if desired. 7. Plug stereo mini plug into MP3/Aux jack. Plug stereo mini plug into MP3 plug from the AC receptacle. 17. The mains plug of the power supply cord shall remain readily operable. The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. player (for example).

The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons. WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture. WARNING: No naked flame sources – such as candles – should be placed on the product. WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel. WARNING:

This product is intended to be operated ONLY from the AC Voltages listed on the back panel or included power supply of the product. Operation from voltages other than those indicated may cause irreversible damage to the product and void the product’s warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate. If the product is equipped with a detachable power cord, use only the type provided with your product or by your local distributor and/or retailer. If you are unsure of the correct operational voltage, please contact your local distributor and/or retailer.

Since the ProMedia 2.1 has its own internal amplifier, it was designed to use the “line out” connector of the computer. Connection to the speaker level output jack might result in poor sound quality. SOFTWARE AND HARDWARE GAIN CONTROLS Software Volume Controls in Microsoft Windows 1. Click the Start button on your taskbar 2. Choose Accessories 3. Windows 95: Choose Multimedia Windows 98/2000/XP/Vista/7: Choose Entertainment 4. Click on the Volume Control 5. Adjust the Wave Volume Elevator Button to 70% CAUTION: Place the equipment near a main power supply outlet and make sure that you can easily access the power breaker switch.

PACKING LIST 2 Satellite speakers with pedestals and wires attached 1 Control pod, attached to one satellite speaker 1 Subwoofer 1 Packet of rubber isolation feet 1 Owner’s manual Volume Control Programs Some soundcard and/or PC manufacturers may have software that must be adjusted separately from the Windows volume control. Consult applicable manual for specific hardware documentation. W A R N I N G RISK OF ELECTRIC SHOCK. DO NOT OPEN.

Стр. 2

Subwoofer Level For CD or DVD output, the optimum position will be indicated by the mark at 10 o’clock on the sub level control. Optimum sub levels and user preference may vary from game to game. Usually a high bass level is preferred, especially at low listening levels. Remember to reset the control settings before playing CDs or films on DVD. CONTROL POD FEATURES If one or more speakers have little or no sound, ensure that:

- All cables are connected properly - Connectors are fully “seated” in soundcard and speakers - Main and subwoofer level controls are properly adjusted on control pod - Computer software audio settings are adjusted for proper use - Computer system’s sound (control panel) volume is turned up Headphones: The 1/8” stereo headphone output jack, located on the right-hand side of the control pod, turns off the two satellite speakers and the subwoofer output. The main volume control will adjust the headphone output. If the satellites or subwoofer exhibit distortion or buzzing:

- Turn down computer’s volume (via control panel), and reduce control pod volume - Turn down subwoofer’s volume, as program signal may be too strong - Plug the subwoofer’s power cord into a surge protector MP3/Aux: The MP3/Auxiliary input jack is used with portable audio players. This signal will be mixed with the main source. The input has a +6dB input sensitivity to help compensate for the lower output voltage of some portable players. To obtain the proper balance with the main signal, the level adjust­ ments in the computer software and in the portable player will need to be adjusted.

An example would be listening to an MP3 player while surfing the net and hearing associated sounds from various websites. The mixed sound may not be desirable, and you will ultimately determine how you use this feature. If there is noise or hissing and the volume is low even when the main volume is up: - Turn up computer’s sound volume (via control panel) - Turn down main volume on control pod to compensate - Ensure that software/hardware is properly installed and operating If there is computer monitor interference: - Make sure the sub is positioned at least 3 feet (1m) from the computer monitor - Increase the distance between the satellite speakers and the computer monitor NOTE:

During playback of MP3s, overall sound quality may be perceptibly degraded compared to other audio sources such as CD. This is caused by the encoding method and quality of the MP3 file. It is recommended that MP3 files be encoded at a minimum 128 bit rate. For more detailed information and FAQs, please visit www.klipsch.com. FCC AND CANADA EMC COMPLIANCE INFORMATION Approved under the verification provision of FCC Part 15 as a Class B Digital Device. SPECIFICATIONS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (Visit www.klipsch.com for more details) Satellite Impedance:

4 ohms minimum (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Preamplifier Control Pod: Subwoofer and Main volume level controls LED power indicator MP3/Aux player line input with soundcard mixing function Headphone jack Direct path interface NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - CAUTION: Changes or modifications not expressly approved by manufacturer could void the user’s authority to operate this device. Satellite: Sealed elliptical two-way enclosure with 25mm metalized polymer dome tweeter mated to MicroTractrixTM Horn and 3” long-throw mid-bass driver Subwoofer: Bass-reflex enclosure with rear port and front-firing 8” long-throw driver; slot tuned port; sixth-order enclosure design Amplifier:

High-efficiency power supply and linear amplifiers designed for uncompressed full power sound Subwoofer Limiter: Protective limiter function protects the driver and amplifier from extremely high volume playback This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numйrique de la classe B est conforme а la norme NMB-003 du Canada. TROUBLESHOOTING If no sound, ensure that:

- Power, input, speaker cables connectors and AC power cord are securely attached - Soundcard software is properly installed and functioning - Computer sound (control panel) volume is turned up and not muted - LED glowing - Headphones are not connected Specifications are subject to change without notice.

Стр. 3

PRODUCT REGISTRATION BENEFITS • Klipsch will keep you up-to-date on new products and promotions • Your personal information will never be resold Register your product online at www.klipsch.com/register

Стр. 4

SPANISH - INSTRUCCIONES IMPORTANTES DE SEGURIDAD LISTA DE EMPAQUE 1. LEA estas instrucciones. 2. GUARDE estas instrucciones. 3. RESPETE todas las advertencias. 4. SIGA todas las instrucciones. 5. NO use este aparato cerca del agua. 6. LHMPIELO SOLAMENTE con un paco seco. 7. NO bloquee las aberturas de ventilaciyn. Instale el aparato de acuerdo con las instrucciones 2 altavoces satйlite con pedestales instalados y cables conectados 1 mydulo de control, montado en uno de los altavoces satйlite 1 subwoofer 1 paquete de patas de aislamiento de goma 1 manual del propietario del fabricante. 8.

NO lo instale cerca de fuentes de calor tales como radiadores, rejillas de calefacciyn, cocinas COLOCACIYN DE LOS ALTAVOCES 1. Los dos altavoces satйlite se deben colocar simйtricamente, uno a cada lado u otros aparatos (incluso amplificadores) que generan calor. 9. NO anule la seguridad implнcita en el enchufe polarizado o con conexiyn a tierra. Los enchufes del monitor de la computadora. Para montar los altavoces en la pared, se pueden quitar los pedestales desatornillando el perno de ј de plg. con rosca 20, que acepta una gran variedad de soportes de pared a la venta en tiendas de estйreos y aparatos elйctricos. 2. Sitъe el subwoofer directamente debajo de la mesa de su computadora.

polarizados tienen dos patas, una mбs ancha que la otra. Los enchufes con conexiyn a tierra tienen dos patas iguales y una clavija de conexiyn a tierra. La pata ancha o la clavija de conex­ iyn a tierra han sido incorporadas al diseco por la seguridad del usuario. Si el enchufe no entra en el tomacorriente, consulte a un electricista para que cambie el tomacorriente obsoleto. 10. EVITE que el cordyn de alimentaciyn sea pisado o aplastado, en particular cerca de los enchufes o tomacorrientes y en el punto en que los cordones salen del aparato. 11. USE SYLO los accesorios especificados por el fabricante. 12.

PONGA el aparato solamente en el carrito, pedestal, trнpode, soporte o mesa espe­ Debe colocar el subwoofer en el suelo cerca de una pared con el panel trasero hacia la pared. No cubra el excitador del subwoofer o el puerto delantero de la caja y asegъrese de que haya suficiente ventilaciyn por la parte de atrбs del subwoofer. Es normal que este panel estй caliente al tacto. El subwoofer debe estar a por lo menos 1 m (3 pies) del monitor de la computadora para evitar la interferencia. 3. Los cables de altavoz o alimentaciyn ubicados en бreas por las cuales pasan cificado por el fabricante o vendido con el aparato.

Sea precavido cuando mueva el aparato en un carrito para evitar las lesiones que pueda producir un volcamiento. 13. DESENCHUFE el aparato durante las tormentas elйctricas o cuando no lo vaya a usar durante largos perнodos de tiempo. 14. ENCARGUE todo servicio al personal de servicio calificado. Se requiere servicio cuando el aparato ha sido dacado de alguna manera, tal como cuando se ha dacado el enchufe o el cordyn de alimentaciyn, han caнdo lнquidos u objetos dentro del aparato, o el aparato se ha de­ jado caer, ha dejado de funcionar normalmente o ha sido expuesto a la lluvia o a la humedad. 15.

NO exponga este aparato a goteras o salpicaduras de agua y asegъrese de que no se le personas se deben colocar contra una pared o esquina y asegurar con cinta adhesiva. DIAGRAMA DE CONEXIYN DE ALTAVOCES coloquen encima objetos llenos de lнquido, tales como floreros. 16. Para desconectar completamente este aparato del suministro de corriente alterna, retire del tomacorriente de corriente alterna el enchufe del cordyn de alimentaciyn. 17. El enchufe del cordyn de alimentaciyn para el tomacorriente de suministro debe quedar 1. No enchufe el cordyn de alimentaciyn de corriente alterna hasta haber configu­ ubicado de manera tal que el usuario pueda manipularlo fбcilmente.

rado la computadora o sistema de sonido. 2. Conecte el enchufe miniatura del preamplificador del satйlite de control a la El signo de admiraciyn dentro de un triбngulo equilбtero tiene por objeto avisar al usuario que hay informaciyn importante sobre operaciyn y mantenimiento (servicio) en los folletos que acompacan al producto. tarjeta de sonido de la PC. Tenga cuidado de no colocar el subwoofer donde estй possible darle patadas, porque esto puede dacar los cabeles. 3. Conecte el enchufe DIN del preamplificador del satйlite de control al subwoofer. 4.

Conecte los altavoces insertando las puntas estacadas de los cables en el El sнmbolo compuesto por un rayo con punta de flecha dentro de un triбngulo equilбtero tiene por objeto advertirle al usuario que dentro del aparato hay “voltajes peligrosos” no aislados cuya magnitud puede ser suficiente para constituir un riesgo de descarga elйctrica para las personas. subwoofer. El cable negro sylido (-) se conecta a las lengьetas con resorte negras; el cable negro con rayas rojas (+) se conecta a las lengьetas con resorte rojas. 5. Enchufe el cordyn de alimentaciyn de corriente alterna en un tomacorriente ADVERTENCIA:

Para reducir el riesgo de incendio o descarga elйctrica, no exponga este aparato a la lluvia o a la humedad. de pared. 6. Si lo desea, inserte el enchufe miniatura estereofynico de los auriculares en ADVERTENCIA: No se deben colocar fuentes de llama expuesta, tales como velas, encima de este producto. el enchufe para auriculares. 7. Inserte el enchufe miniatura estereofynico en el enchufe MP3/Aux. Inserte el enchufe miniatura estereofynico en un reproductor MP3 (por ejemplo). A D V E R T E N C I A RIESGO DE DESCARGA ELЙCTRICA. NO ABRIR. ADVERTENCIA. No abrir. Riesgo de descarga elйctrica. Los voltajes que hay dentro de este equipo son peligrosos para los seres vivos.

Dentro del dispositivo no hay piezas que el usuario pueda reparar. Encargue todo servicio al personal de servicio calificado. ADVERTENCIA. Este producto ha sido disecado para funcionar EXCLUSIVAMENTE con los voltajes de corriente alterna indicados en el panel de atrбs o con la fuente de alimentaciyn incluida. El funcionamiento con voltajes no indicados puede causar dacos irreversibles al producto y anular la garantнa. Se recomienda usar con precauciyn los adaptadores de enchufe de corriente alterna porque pueden permitir que el producto se conecte a voltajes para los cuales no ha sido disecado.

Si el producto tiene un cordyn de alimentaciyn desprendible, utilice exclusivamente el tipo de cable que viene con el producto o el que incluye su distribuidor y/o minorista local. Si no estб seguro del voltaje correcto de funcionamiento, comunнquese con su distribuidor y/o minorista local. PRECAUCIYN: Coloque el equipo cerca de un tomacorriente principal de alimentaciyn y asegъrese de poder alcanzar fбcilmente el interruptor de alimentaciyn. Como tiene su propio amplificador interno, el ProMedia 2.1 ha sido disecado para conectarse al enchufe de salida de nivel de lнnea de la computadora. La conexiyn al enchufe de salida de nivel de altavoz puede producir mala calidad de sonido.

Стр. 5