2009 — Sealed Splice Connector Repair

HOME A.18 SEALED SPLICE CONNECTORS SEALED SPLICE CONNECTOR REPAIR 5. Squeeze the handles tightly closed to crimp the lead in the insert (2). The tool automatically opens when the crimping is complete. TOOL NAME PART NUMBER ROBINAIR HEAT GUN HD-25070 6. Slide the connector to the other half of the metal insert. Insert the stripped wire lead (1) until it stops, and crimp the lead in the insert (2). PACKARD CRIMPING TOOL HD-38125-8 ULTRA TORCH UT-100 HD-39969 HEAT SHIELD ATTACHMENT HD-41183 General Be sure to follow manufacturer's instructions when using the UltraTorch UT-100 or any other radiant heating device.

Failure to follow manufacturer's instructions can cause a fire, which could result in death or serious injury. (00335a) Splice connectors and several OE ring terminal connectors use heat shrink covering to seal the connection. Preparing Wire Leads • Avoid directing heat toward any fuel system component. Extreme heat can cause fuel ignition/explosion resulting in death or serious injury. If adjacent wires are to be spliced, stagger the splices so that the sealed splice connectors will not touch each other but are located at different positions along the length of the wires.

NOTE • Avoid directing heat toward any electrical system com- ponent other than the connectors on which heat shrink work is being performed. 1. Using a shop gauge, identify the gauge of the wire. 2. Match the wire gauge to a sealed splice connector by color and part number. Refer to Table A-5 . • Always keep hands away from tool tip area and heat shrink attachment. NOTE If any copper wire strands are cut off of the wire core, trim the end and strip the wire again in a larger gauge stripper. Splicing Wire Leads NOTE See Figure A-54 . The connector is crimped twice - one side and then the other. 1. See Figure A-53 . Open the PACKARD CRIMPING TOOL (Part No.

HD-38125-8) ratchet by squeezing the handles closed. 2. Match the connector color to the wire gauge crimp die in the jaws and insert one end of the sealed connector. 3. Gently squeeze the handles until the connector is held in the jaws. 4. See Figure A-54 . Feed the stripped end of a wire into the connector until the wire stops inside the metal insert (1). 2009 VRSC Service: Appendix A Connector Repair A-35 7. Use an ULTRA TORCH UT-100 (Part No. HD-39969) 3. Using a wire stripper, cut and strip a length of insulation a ROBINAIR HEAT GUN (Part No. HD-25070) wit off the wire ends. Refer to Table A-5 for the strip length. HEAT SHIELD ATTACHMENT (Part No.

HD-41183) heat the connector from the center of the crimp (3) ou Table A-5. Sealed Splice Connectors each end. WIRE GAUGE COLOR PART NO. STRIP LENGTH NOTE 18-20 Red 70585-93 9.5 mm (3/8 in.) It is acceptable for the splice to rest against the heat sh (0.5-0.8 mm) tool attachment. 14-16 Blue 70586-93 9.5 mm (3/8 in.) Inspecting Seals (1.0-2.0 mm) See Figure A-54. Allow the splice to cool and inspect the s 10-12 Yellow 70587-93 9.5 mm (3/8 in.) (3.0-5.0 mm) The insulation should appear smooth and cylindrical. Me RA TORCH UT-100 (Part No. HD-39969) Table A-5. Sealed Splice Connectors WIRE GAUGE 18-20 (0.5-0.8 mm) COLOR Red PART NO.

70585-93 STRIP LEN 9.5 mm (3/ 14-16 (1.0-2.0 mm) Blue 70586-93 9.5 mm (3/8 in.) 9.5 mm (3/8 in.) 10-12 (3.0-5.0 mm) Yellow 70587-93