2009 — TORQUE VALUES

2009 VRSC Models Service Manual FASTENER TORQUE VALUE NOTES Clutch master cylinder/reservoir, sec- ondary clutch actuator cover mounting bolts 6-10 Nm 53-88 in-lbs 2.11 CLUTCH MASTER CYLINDER AND RESERVOIR, Installation Clutch side crankcase cover fasteners 9.7 Nm 86 in-lbs 6.2 CLUTCH, Installation Coil fasteners 9.7 Nm 86 in-lbs 1.22 SPARK PLUGS AND COIL, Installation Coil fasteners 9.7 Nm 86 in-lbs 4.7 THROTTLE BODY AND FUEL RAIL, Installa- tion Compensator bowl screws 75-88 Nm 55-65 ft-lbs 2.26 REAR WHEEL, Assembly Compensator bowl screws (final torque) 102-115 Nm (final torque) 75-85 ft-lbs 2.26 REAR WHEEL, Assembly Connecting rod caps 27 Nm 20 ft-lbs 3.11 ENGINE BOTTOM END SERVICE, Crank- shaft, Piston and Cylinder Liner Removal/Installa- tion/Tighten to torque and then tighten an additional 90 degrees Connecting rod caps 27 Nm 20 ft-lbs 3.11 ENGINE BOTTOM END SERVICE, Crank- shaft, Piston and Cylinder Liner Removal/Installa- tion/Tighten to torque and then tighten an additional 90 degrees Coolant air bleed plug 9-11 Nm 80-97 in-lbs 2.7 ENGINE REPLACEMENT, Installation Coolant drain plug 2.3-2.8 Nm 21-24 in-lbs 5.3 ENGINE COOLANT, Replacing Coolant Cooling fan fasteners 7.28 COOLING FANS, Assembly 5-7 Nm 44-62 in-lbs Cooling system, cross member fasten ers 20-26 Nm 15-19 ft-lbs 2.7 EN GINE REPLACEMENT, Installation Cooling system, hose worm drive clam ps 3-4 Nm 27-35 in-lbs 2.7 ENGINE REPLACEMENT, Installation Cooling system, P-clamp 6-10 Nm 53-88 in-lbs 2.7 ENGINE REPLACEMENT, Installation Cooling system, pipe clamp 6.5 Nm 57 in-lbs 2.7 ENGINE REPLACEMENT, Installation Cooling system, pipe connecting clamp 6-10 Nm 53-88 in-lbs 2.7 ENGINE REPLACEMENT, Installation Cooling system, top mounting flange nuts 19-27 Nm 15-20 ft-lbs 2.7 ENGINE REPLACEMENT, Installation Counterbalancer gear fastener 50 Nm 37 ft-lbs 6.3 TRANSMISSION, Assembly Counterbalancer gear fastener 50 Nm 37 ft-lbs 6.4 COUNTERBALANCER BEARING REPLACE- MENT, Installation Crank position sensor fastener 8.2-10.7 Nm 73-95 in-lbs 7.18 CRANK POSITION SENSOR (CKP), Installa- tion Cross member fasteners 20-26 Nm 15-19 ft-lbs 5.8 RADIATOR AND OIL COOLER, Installation Cross member mounting bolts 20-26 Nm 15-19 ft-lbs 2.3 FRAME AND LOWER FRAME RAILS, Installa- tion Crossover TORCA clamp 13-15 Nm 1 4.16 EXHAUST SYSTEM:

VRSCF, Installation 15-133 in-lbs Cylinder head exhaust flange nuts, front 8-12 Nm 7 4.16 EXHAUST SYSTEM: VRSCF, Installation 1-106 in-lbs Cylinder head exhaust flange nuts, rear 8-12 Nm 7 4.16 EXHAUST SYSTEM:

VRSCF, Installation 1-106 in-lbs Debris deflector fastener 6-10 Nm 53-88 in-lbs 1.18 DRIVE BELT REPLACEMENT, Replacement Debris deflector fastener 2.26 REAR WHEEL, Installation 6-10 Nm 53-88 in-lbs 2.26 REAR WHEEL, Inst Debris deflector fastener 6-10 Nm 53-88 in-lbs 2.36 BELT GUARD AND DEFLECTOR, Installatio DEBRIS n Derby cover fastener 8.2-10.7 Nm 72-95 in-lbs 7.19 ALTERNATOR, Inst allation Drain plug 35 Nm 25.8 ft-lbs 1.2 MAINTENANCE SC HEDULE, General Drain plug 2.3-2.8 Nm 21-24 in-lbs 1.2 MAINTENANCE SC HEDULE, General TORQUE VALUES XI