Delta Electronics AH500 — 11.1.3.1 Parameters Related to a PLC Link

AH500 Operation Manual 11.1.3 Executing a PLC Link through the Program in ISPSoft Users can execute a PLC Link through the program in ISPSoft. The setting of the parameters related to a PLC Links is described in this section. Users can execute a PLC Link efficiently. 11.1.3.1 Parameters Related to a PLC Link 1. The special data registers and the special auxiliary relays for slave 1~slave 32 are described below. *. SM1424~SM1583 are read-only devices.  Start address in the master station: The start address in the master station is a device address. The default start address in the master station is D0.

If the AH500 Modbus communication protocol is used, the start address in the master station is an AH500 Modbus device address. If the standard Modbus communication protocol is used, the start address in the master station is a Modbus device address. The data in the device addresses in the master station starting from the start address in the master station is sent to a slave, and the data sent by a slave station is stored in the devices in the master station starting from the start address in the master station. If the communication protocol used is the standard Modbus communication protocol, only M0~M8191 and D0~D32767 can be used.

If the communication protocol used is the AH500 Modbus communication protocol, only M0~M8191, 11-20 Master station Slave station 1 Slave station 2 … Slave station 32 Read Write Read Write … Read Write Latched area Address in the master: The device address into which the data is read (SR1404 and SR1405) Address in the master: The device address from which the data is written (SR1468 and SR1469) Address in the master: The device address into which the data is read (SR1406 and SR1407) Address in the master: The device address from which the data is written (SR1470 and SR1471) … Address in the master: The device address into which the data is read (SR1466 and SR1467) Address in the master:

The device address from which the data is written (SR1530 and SR1531) Address in the slave: The device address from which the data is read (SR1532 and SR1533) Address in the slave: The device address into which the data is written (SR1596 and SR1597) Address in the slave: The device address from which the data is read (SR1534 and SR1535) Address in the slave: The device address into which the data is written (SR1598 and SR1599) … Address in the slave: The device address from which the data is read (SR1594 and SR1595) Address in the slave:

The device address into which the data is written (SR1658 and SR1659) Number of data which is read from the slave (SR1660) Number of data which is written into the slave (SR1692) Number of data which is read from the slave (SR1661) Number of data which is written into the slave (SR1693) … Number of data which is read from the slave (SR1691) Number of data which is written into the slave (SR1723) Device type (SR1340) Device type (SR1372) Device type (SR1341) Device type (SR1373) … Device type (SR1371) Device type (SR1403) Type of slave 1 (SR1724) Type of slave 2 (SR1725) … Type of slave 32 (SR1755) Address of slave 1 (SR1756) Address of slave 2 (SR1757) …

Address of slave 32 (SR1787) PLC Link flag (SM1392) PLC Link flag (SM1393) … PLC Link flag (SM1423) Non-latched area Data exchange flag (SM1424) Data exchange flag (SM1425) … Data exchange flag (SM1455) Read error flag (SM1456) Write error flag (SM1488) Read error flag (SM1457) Write error flag (SM1489) … Read error flag (SM1487) Write error flag (SM1519) The data reading is complete. (ON->OFF) (SM1520) The data reading is complete. (ON->OFF) (SM1521) … The data reading is complete. (ON->OFF) (SM1551) The data writing in the PLC Link is complete. (ON->OFF) (SM1552) The data writing in the PLC Link is complete. (ON->OFF) (SM1553) … The data writing in the PLC Link is complete.

(ON->OFF) (SM1583)