. MAINTENANCE TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE SPECIFICATIONS TIGHTENING TORQUE LIST CAUTION Apply the following table for Hydraulic Hose. 4 - 12 If nuts, b olts, or oth er parts are not tightened to th e specified torque, i t wil l cause looseness or dam age to the tightened parts , and this will cause fail ure of the ma chine o r problem s with operation. Always p ay carefu l attention w hen tightening pa Unless otherwis e specified , tighte n the met ric nuts and bolts to t he torque shown in the table below. If it is ne cessary to replace any nut or bolt, always use a Komatsu genuine part of the sa me size as the part that was replaced.
Thread diameter of bolt (a)(mm) Width across flats (b)(mm) Tightening torque Target value Service limit Nm kgm lbft Nm kgm lbft 6 8 10 12 14 10 13 17 19 22 13.2 31 66 113 172 1.35 3.2 6.7 11.5 17.5 9.8 23.1 48.5 83.2 126.6 11.8-14.7 27-34 59-74 98-123 153-190 1.2-1.5 2.8-3.5 6.0-7.5 10.0-12.5 15.5-19.5 8.7-10.8 20.3-25.3 43.4-54.2 72.3-90.4 112.1-141 16 18 20 22 24 24 27 30 32 36 260 360 510 688 883 26.5 37 52.3 70.3 90 191.7 267.6 378.3 508.5 651 235-285 320-400 455-565 610-765 785-980 23.5-29.5 33.0-41.0 46.5-58.0 62.5-78.0 80.0-100.0 170.0-213.4 238.7-296.6 336.3-419.5 452.1-564.2 578.6-723.3 27 30 33 36 39 41 46 50 55 60 1295 1720 2210 2750 3280 132.5 175.0 225.0 280.0 335.0 958.4 1265.8 1627.4 2025.2 2423.1 1150-1440 1520-1910 1960-2450 2450-3040 2890-3630 118.0-147.0 155.0-195.0 200.0-250.0 250.0-310.0 295.0-370.0 853.5-1063.3 1121.1-1410.4 1446.6-1808.3 1808.3-2242.2 2133.7-2676.2 Hose nominal number Width across flat a (mm) Tightening torque Target valve Service limit Nm kgm lbft Nm kgm lbft 02 19 44 4.5 32.5 35-54 3.5-5.5 25.3-47.0 03 22 74 7.5 54.2 54-93 5.5-9.5 39.8-68.7 24 78 8.0 57.9 59-98 6.0-10.0 43.4-72.3 04 27 103 10.5 75.9 84-132 8.5-13.5 61.5-97.6 05 32 157 16.0 115.7 128-186 13.0-19.0 94.0-137.4 06 36 216 22.0 159.1 177-245 18.0-25.0 130.2-180.8